OKI C130n User Manual

							161 - C130n User’s Guide
8Load paper into Tray 2. See 
“Tray 2” on page 65. 
9Insert Tray 2 into the printer and 
reconnect all interface cables.
10Reconnect the power cord, and 
turn on the printer.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
11Activate Tray 2 in the Windows printer driver (Properties/Configure tab, 
see 
page 17).
Downloaded From ManualsPrinter.com Manuals 
						

							162 - C130n User’s Guide
Duplex Option
Duplex printing (printing on both sides of the page) can be performed 
automatically with the duplex option installed. 
For more information, see “Duplexing” on page 68.
Before installing the duplexer, you must first install one of the following on the 
printer:
!Optional Tray 2
!The duplexing attachment (1) supplied with the Duplexer (2)
Installing the Duplexing Attachment
Important!
If Tray 2 is installed, it is not necessary to install the duplex 
attachment. In this case, skip “Installing the Attachment”, and 
continue with “Installing the Duplex Option” on page 174.
The duplexing attachment (or optional Tray 2) must installed before the 
duplexer can be installed.
NoteThe duplexing attachment cannot be used by itself; it must be used 
together with the duplexer.
Downloaded From ManualsPrinter.com Manuals 
						

							163 - C130n User’s Guide
Important!
Since the imaging drum and toners are installed in the printer, be 
sure to keep the printer level when moving it in order to prevent 
accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Remove the dust cover from 
Tray
 1. 
Downloaded From ManualsPrinter.com Manuals 
						

							164 - C130n User’s Guide
3Close Tray 1 and the output tray.  
 
 
 
 
 
 
 
 
 
 
 
4Unpack the duplexing attachment.
NoteBe sure to place the attachment on a level surface.
5Lift the printer and place it on top 
of the attachment, making sure 
that the positioning pins on the 
attachment correctly fit into the 
holes on the bottom of the 
printer.
 
 
 
 
 
 
 
 
6Open Tray 1 and the output tray, and reattach the dust cover.
Downloaded From ManualsPrinter.com Manuals 
						

							165 - C130n User’s Guide
Installing the Duplexer
NoteThe illustrations in the following installation procedure show the printer 
with Tray
 2 installed; however, the installation procedure would be the 
same if the attachment was installed.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Remove the tape affixed to the 
rear cover.
3Unpack the duplexer.
Downloaded From ManualsPrinter.com Manuals 
						

							166 - C130n User’s Guide
4Install the duplexer. 
Align the duplex option with its 
installation position, and then 
push down on the bottom of the 
duplex option until it locks into 
place.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Important!
When attaching the duplex option, attach the bottom of the option 
first. If the duplex option is attached incorrectly, it may be 
damaged.
Downloaded From ManualsPrinter.com Manuals 
						

							167 - C130n User’s Guide
5Open the duplex cover. 
While holding the duplex option 
against the printer, tighten the 
screws inside the cover to 
complete the installation of the 
duplex option.
 
 
 
 
 
 
 
 
6Reconnect all interface cables.
7Reconnect the power cord, and 
turn on the printer.
8Activate the duplexer in the Windows printer driver (Properties/Configure 
tab, see 
page 17).
Downloaded From ManualsPrinter.com Manuals 
						

							168 - C130n User’s Guide
Specifications
10
Downloaded From ManualsPrinter.com Manuals 
						

							169 - C130n User’s Guide
Printer Specifications 
Ty p eDesktop full color laser beam printer
Printing systemDual laser diode with polygon mirror
Developing systemMono component development system
Fusing systemHeat roller system
Resolution600 dpi × 600 dpi × 4 bits or  
600 dpi × 600 dpi × 1 bit
First printSimplex
Monochrome: 
13.0 seconds for A4, Letter (plain paper)
Full color: 
22.0 seconds for A4, Letter (plain paper)
Duplex
Monochrome: 
26.0 seconds for A4, Letter (plain paper)
Full color: 
35.0 seconds for A4, Letter (plain paper)
Print speedSimplex
Monochrome: 
20.0 pages per minute for A4, Letter (plain 
paper)
Full color: 
5.0 pages per minute for A4, Letter (plain 
paper)
Duplex
Monochrome: 
13.2 pages per minute for A4, Letter (plain 
paper)
Full color: 
5.0 pages per minute for A4, Letter (plain 
paper)
Warm-up timeAvg. 45 seconds (time to return to Ready mode 
from Energy save mode) 
Downloaded From ManualsPrinter.com Manuals 
						

							170 - C130n User’s Guide
Media sizesTray 1
Paper width: 92 to 216 mm (3.6 to 8.5)
Paper length:
Plain paper: 
195 to 356 mm (7.7 to 14.0)
Thick stock 1/2: 
184 to 297 mm (7.25 to 11.7)
Tray 2 (Optional)
A4/Letter
Paper/MediaPlain paper (60 to 90 g/m2; 16 to 24 lb bond)
Thick stock 1 (91 to 163 g/m2)
Thick stock 2 (164 to 209 g/m2)
Postcard
Letterhead
Label sheet
Input capacityTray 1
Plain paper: 200 sheets
Label/Letterhead/Postcard/Thick Stock: 
50 sheets
Tray 2 (Optional)
Plain paper: 500 sheets
Output capacityOutput tray: 100 sheets (A4, Letter)
Operating temperature10 to 35°C (50 to 95°F) 
Operating humidity15 to 85%
Power supply120 V, 60 Hz 
220 to 240 V, 50 to 60 Hz 
Power consumption120 V: 1050 W or less
220 to 240 V: 1100 W or less
Energy Saver Mode: 18.5 W or less
Amperage120 V: 8.4 A or less 
220 to 240 V: 4.4 A or less 
Acoustic NoisePrinting: 52 dB or less
Standby: 32 dB or less
Downloaded From ManualsPrinter.com Manuals