Oce ColorWave 300 User Manual

Description / Function
Component
Guides the original over the scanner to the
front.
original guide
-
When to do The 
copy and scan quality can decrease if
■ the
 transparent contact 
plates (8) are dirty or static.
■ The
 
original support rollers (5) are dirty and you use transparent originals.
In
 that 
case you must clean the scanner to ensure top quality output.
How
 to clean the scanner 1. Use 
both hands to push up the left and right scanner open levers (4) to fully open the
scanner top 
cover (3)....

A locking mechanism prevents the scanner top cover from closing.
Caution:
To clean the scanner use the soft lint-free Masslin towels from the scanner cleaning kit.
2. Use 
a Masslin towel that has been moistened with water and firmly wrung out to clean
the following parts of the scanner. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer292Clean the scanner
Downloaded From ManualsPrinter.com Manuals     

■
the original support rollers (5)
Rotate
 
the rollers to clean them.
■ the transparent contact 
plates (8)
Wipe
 
off any soiled areas. 3. Wipe 
all the cleaned parts once again using a dry Masslin towel.
Warning:
Take care not to get your fingers caught in the scanner top cover.
4.
Press the scanner top 
cover down gently with both hands to close it.
Note:
Check that the left and right scanner open levers are locked into position. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer...

Calibrate the scanner
Introduction
You can calibrate the scanner when you are not satisfied with the copy or scan quality.
Use
 
the calibration wizard on the printer user panel to calibrate the scanner.
Before
 you begin Clean 
the scanner before you start the calibration procedure. Dirty parts of the scanner
causes
 a decreased copy and scan quality. (See ‘Calibrate the scanner’  
on page 294 ).
Caution:
Handle the calibration sheet with care.
Caution:
Do not touch the black area of the calibration...

5.
Insert the scanner calibration sheet¹ as instructed in the wizard.
6. Press
 the start 
button to start the scanner calibration.
The
 
message 'Calibrating, please wait... do not open the scanner.' appears.
Note:
'Calibrating the scanner takes between 5 to 10 minutes.'
Note:
¹ The scanner calibration sheet code number is 97002634. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 295Calibrate the scanner
Downloaded From ManualsPrinter.com Manuals 

Chapter 7 - Maintain the Océ ColorWave 300 multifunction printer296Calibrate the scanner
Downloaded From ManualsPrinter.com Manuals 

Chapter 8
System 
messages and so-
lutions
Downloaded From ManualsPrinter.com Manuals 

The printer
Overview
Definition
This table gives an overview of the possible error messages and system messages of the
printer
 and refers to 
the possible solution. #
Description / solution
Error message / System mes-
sage
The media required for the job is not available on
the printer.
See

 
‘Replace / Install the media’  on page 272
'Required
 
media not available'
The end of the roll of media is reached while you
print
See 
‘Replace / Install the media’  on page 272
'Roll
 
empty'
A...

#
Customer action
Description
Error
code
Replace the printhead by using the
wizard.
Note:
Never re-insert a printhead
that
 has caused this problem. Excessive leakage current detect-
ed for head [1…9]
Printhead

 failing
Replace

 
printed [1…9]
4501
 -
4509
Printhead is probably not 
placed
correctly. Remove and re-insert the
printhead

 at 
the original position.
Note:
If the problem persists you
must replace the printhead. Head 
defective during printing
4551 -
4559
You can 
ignore this problem by...

Cover or door opened
Cover or door opened
When you open a cover accessing the wizard, the system produces a double warning signal.
When you open a door or cover during printing, the printer stops. A message on the
printer
 user panel tells you 
to close the cover. Close the cover to continue. Examples:
Chapter 8
 - System messages and solutions300Cover or door opened
Downloaded From ManualsPrinter.com Manuals