Oce ColorWave 300 User Manual

Chapter 7
Maintain 
the Océ Color-
Wave 
300 multifunction
printer
Downloaded From ManualsPrinter.com Manuals 

Replace the media
Replace / Install the media
Introduction
The standard configuration of the Océ ColorWave 300 contains two rolls of media .
Appendix
 A contains a list of the supported media types 
and media sizes.
This
 
section describes how to remove and load a roll of media .
When
 to do Change a roll when 
a job needs a media type or size that is not on one of the rolls.
Change
 the media type that 
is defined on the system when the defined media type and
the
 available media type do not...

2.
Use both hands to remove the roll. [221]
 Remove the roll
3. Both far ends of the roll contain roll holders with handles. Lift the handles to release the
roll holders. [222]
 Release the roll holders
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 273Replace / Install the media
Downloaded From ManualsPrinter.com Manuals     

4.
Remove the roll holders. [223] Remove the roll holders
How to load a new media roll 1.Insert

 the roll holder in 
both ends of the new media roll.
2. Press the handles down to 
fasten the roll holders.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer274Replace / Install the media
Downloaded From ManualsPrinter.com Manuals   

3.
Put the saddles into position at the ends of the track. [224]
 Saddles
4. Use 
both hands to place both roll holders in the green saddles on the printer.
5. Use
 
both hands to slide the medium under the paper guide. Place the media on the
printer
 as 
shown in the figure below. The 
medium loads into the printer from the top of the media roll.
Make sure 
the medium makes contact with the paper guide.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 275Replace / Install the media...

6.
The printer automatically draws the medium into the correct position.
7. The
 
user panel displays the message 'New media detected on roll 1' or 'New media de-
tected
 on roll 2'. 
Follow the steps in the wizard to define the correct media type. The
media
 size 
is detected automatically.
Note:
The printer automatically detects the width of the media. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer276Replace / Install the media
Downloaded From ManualsPrinter.com Manuals 

Ink
Replace the ink tanks
Introduction
The Océ ColorWave 300 contains the following four ink tanks.
■ One
 tank for the cyan ink.
■ One

 tank for the magenta 
ink.
■ One tank for the yellow ink.
■ One

 tank for the black 
ink.
The ink level card on the printer user panel indicates the ink level of each color as a per-
centage.
You can 
replace the ink tanks at any time. A wizard is not required.
When to do You must replace an ink tank when the ink level indicator on the printer user panel shows
0%....

Use the scroll wheel to go to the 'Ink tank'('Replace ink tank') wizard.
Open this section with 
the confirmation button.
2.
Press the ink tank inward and upward to 
release the ink tank.
3. Pull
 
the ink tank straight out of the slot.
The
 indication for the removed tank on the printer user panel changes into a dashed line. How to place an ink tank
Caution:
Make sure that you only use Océ ColorWave 300 ink tanks. Using other ink tanks will
damage your 
printer!
Caution:
Make sure that...

Note:
Do not shake the ink tank or touch the opening of the ink tank.2.
Slide 
the ink tank into the slot until you feel a resistance and stop.
Note:
The ink tank fits only in one way . The ink tank fits only into the slot dedicated for the
color.
 When you 
attempt to place the ink tank the wrong way or in the wrong slot, the
ink tank will 
not fit. Do not attempt to force it. 3.
Press the ink tank inward and downward until 
the ink tank clicks into place.
When the printer detects the full
 ink tank,...

Replace a defective printhead
Introduction The 
Océ ColorWave 300 contains the following nine printheads.
Overview
 printheads #
Printhead position (indicated on the printhead
carriage)
Color
Quantity
1,
 2, 3
Black (K)
3
4,
 5
Cyan (C)
2
6,
 7
Magenta (M)
2
8,
 9
Yellow (Y)
2
Always follow 
the instructions in the wizard on the printer user panel when you replace
a defective printhead.
After

 you replace a defective printhead, the system performs an alignment. The alignment
requires the use of media....