Oce ColorWave 300 User Manual

Check the output quality of the printer
'Demo print'
Introduction
You can make a 'Demo print' to get an impression of the print capabilities of the Océ
ColorWave
 300.
Use

 
the 'Test prints'('Print a demo or test image') wizard on the printer user panel to
trace
 
output quality problems. ‘Output quality problems’  on page 258
How
 to make a demo print The

 system prints the 'Demo print' in the 'Release' quality mode. The demo print takes
several minutes...

5. Use the scroll wheel to select the 'Demo print'.
6.
 Press the start button.
Chapter 6
 - Ensure the best output quality252'Demo print'
Downloaded From ManualsPrinter.com Manuals 

'Quality check' print
Introduction
The 'Quality check' print option is a quick method to help you find the cause of an un-
satisfactory output quality. The 'Quality check' print option is especially useful to check
the quality of printed lines.
Use
 
the 'Test prints'('Print a demo or test image') wizard on the printer user panel to
trace
 
output quality problems. ‘Output quality problems’  on page 258
How
 to make a quality check print The

 system prints the...

'Tone scale area check' print
Introduction The 'Tone scale area check' print option can be used, upon request of a helpdesk, to in-
dicate 
areas with unsatisfactory output quality.
Illustration [204]
 Tone scale area check test print
How to make a 'Tone scale area check' print The

 
system prints the 'Tone scale area check' print in the 'Presentation' quality mode.
You
 are 
recommended to use A0 / 36" for the 'Tone scale area check' print.
Do
 
the...

Use the 'Tone scale area check' print to test the scanner
On
 
request of the helpdesk the 'Tone scale area check' print can be used to indicate
scanner problems. Use 
the 'Scan to USB' option.
1.
 Feed the 'Tone scale area check'print face up, landscape and centered on the original
feeding
 table.
2.
 Select 'Scan' on the user panel.
3.
 Open the 'Scan' tab with the confirmation button above the scroll wheel.
4.
 Use the scroll wheel to select or create a...

'Color reference chart' print
Introduction
The 'Color reference chart' print gives an overview of the print job settings, copy job
settings
 and advised media settings for a specific input type.
Use

 
the 'Test prints'('Print a demo or test image') wizard on the printer user panel to
print
 the 'Color Reference Chart'.
Illustration [205]
 Color reference chart
Chapter 6
 - Ensure the best output quality256'Color reference chart' print
Downloaded From...

How to make a 'Color reference chart' print
1. From the'HOME' screen select the 'System' tab.
2.
 Select the 'Setup' tab.
3.
 Use the scroll wheel to go to the 'Test prints'('Print a demo or test image') wizard.
Open
 this section with 
the confirmation button.
4.
 Use the scroll wheel to select the 'Color reference chart'.
5.
 Press the start button. 6.
 The 'First language:' setting (in the Océ Express WebTools) is used for the language...

Output quality problems
Introduction
The Océ ColorWave 300 offers three possibilities to check the quality of your printed
output. ■ Make a quality check print
■ Make

 a tone scale area print
■ Make

 a demo print.
This

 section describes the problems you can analyze by making one of these check prints.
The 
Optimize print quality  section describes how you can solve problems with the
quality ‘Optimize the output quality on the printer ’
 on page 263.
Overview of output quality problems - Graininess...

Overview of output quality problems - Stripes and Banding
Stripes and Banding problems #
Description
Graphical representation of the prob-
lem
Small stripes over the entire width of
the print (color independent)
Perform an 'Optimize print quality' test.Note:
This problem can occur in all
print modes. ■
Thin (White) Stripes or weak lines
(Nozzle dropouts)
■ Stripes per primary color
■ Stripes in parts / dotted lines but
also over the entire width
Usually you will find these stripes only in
the...

Description
Graphical representation of the prob-
lem
Stripes perpendicular to the paper feed
direction
In check mode the width of these lines is
12 mm.
In release mode the lines are smaller (3-6
mm) and less 
visible.
Perform an 'Optimize print quality' test.
Note:
After the 'Optimize print quality'
test is completed, the printer may
ask you to replace a printhead. In
this case, 
take out the printhead
and
 clean the contact area with a
lintfree 
cloth and re-insert the
printhead.
If...