Nortel Modular Ics 6.1 System Coordinator Guide

Using the Hospitality features / 191
P0603535  02 Modular ICS 6.1 System Coordinator Guide
Programming the alarm feature
If you want to allow the room sets to program wake-up alarms, 
there are a couple of program settings that need to be entered.
1. Place the appropriate programming overlay on the set you 
are using to do programming.
2. Press ²¥¥ÛßßÜÝÝ (CONFIG). The 
display shows Password:.
3. Press ÛÜßÝß (ADMIN). The display shows 
Terminals&Sets.
4. Press ‘ until the display shows Hospitality.
5....

192 / Using the Hospitality features
Modular ICS 6.1 System Coordinator Guide P0603535  02
19. Press CHANGE to choose either Y (yes) or N (no). 
20. Press ¨ to exit or ‘ to continue programming.
Using the Administration set to control alarms
Only a Hospitality Services set can use this alarm 
administration feature. This feature is also associated with a 
room number, and cannot be used on common sets.
Use this feature to:
query a current or last alarm time set for a room
assign an alarm time for any...

Using the Hospitality features / 193
P0603535  02 Modular ICS 6.1 System Coordinator Guide
If the clock uses a 12-hour format, enter the time, then 
when the set displays: hh:mm AM or PM?, press AM
 or PM. 
The set displays: Alarm ON hh:mm.
5. Press ¨ to exit.
Using the alarm
To set an alarm on a digital telephone:
1. Press ²¡àÞ.The displays shows Alrm:07:00 
OFF
2. Do one of the following:
If the alarm is correct, press ON/OFF
.The set displays: 
Alrm:07:00am ON. Press DONE
 to exit.
If you need to...

194 / Using the Hospitality features
Modular ICS 6.1 System Coordinator Guide P0603535  02
To enter a new time, repeat the above steps and enter a new 
time. This overwrites the existing entry.
Canceling an alarm
Canceling the alarm time for any set cancels the alarm time for 
all the sets in the same room.
Digital set: Press ²£¡àÞ.
Analog set: Press ˚£¡àÞ.
Turning off an alarm
When the alarm rings, the user can release the ring by doing 
one of the following, depending on the type of set in the room:...

P0603535  02 Modular ICS 6.1 System Coordinator Guide
Telephone features
Installing Business Series Terminals
If you are connecting a Business Series Terminal for the first 
time, refer to the following illustrations as a guide.
Installing the Business Series Terminal connections
Installing to a desk jack 

196 / Telephone features
Modular ICS 6.1 System Coordinator Guide P0603535  02
Mounting a Business Series Terminal on the wall
Mounting a Business Series Terminal using the stand
Installing without the angled base
Mount the telephone onto the
    screws and slide it down.Mount the stand as shown and
insert screw. Use the screw that
came with your keystation.
 
Connect line cord to 
wall jack.  Connect cords to the  telephone,
    refer to cord connections
 Tighten screws for a secure fit. 

Telephone features / 197
P0603535  02 Modular ICS 6.1 System Coordinator Guide
Installing Norstar telephones
If you are connecting a Norstar telephone for the first time, 
refer to the following illustrations as a guide.
Installing a Norstar telephone
Connect to 
jack wired from
distribution block
Connect to 
receiver 

198 / Telephone features
Modular ICS 6.1 System Coordinator Guide P0603535  02
Mounting a Norstar telephone on the wall
12
34
56 

Telephone features / 199
P0603535  02 Modular ICS 6.1 System Coordinator Guide
Naming a telephone or a line
You can assign names to identify external lines, target lines, 
and each telephone. During a call, the name, if programmed, is 
shown on the telephone display instead of the external line 
number or internal telephone number of the caller. Step-by-
step instructions for adding or changing the name of a 
telephone or a line are in Changing the name of a telephone on 
page 34.
Telephone names and...

200 / Telephone features
Modular ICS 6.1 System Coordinator Guide P0603535  02
a telephone and cancel the programming, ensure that the 
relocation setting is off.
Stopping calls from ringing at your 
telephone: Do Not Disturb (DND)
Stopping calls
Press ²¡Þ to stop calls from ringing at your telephone.
Only priority calls ring at your telephone. A line button flashes 
when you receive a call, but the call does not ring. 
Refusing to answer a call
While you are on a call, you can refuse to answer a second...