Nortel Modular Ics 6.1 Installer Guide

System prgrming / 421
P0603534  02Modular ICS 6.1 Installer Guide
• When set to Cycle, the system will choose the codes in 
sequence, from lowest to highest, until all the codes have 
been used.
Trnsfr callbk
Transfer callback delay allows you to specify the number of 
rings before a callback occurs on a transferred call. 
Press CHANGE
 to select the setting: 3, 4, 5, 6, or 12 rings.
DRT to prime
Delayed Ring Transfer automatically forwards unanswered 
external calls to a prime telephone after a certain...

422 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
Press CHANGE to select the setting: 1, 2, 3, 4, 6, or 10 rings.
Held reminder
When active, Held Line Reminder reminds you that a call at 
your telephone is still on hold. You periodically hear two tones 
from your telephone until you return to the call on hold. 
Press CHANGE
 to select the setting: N (No) or Y (Yes).
Remind delay
Held Line Reminder delay allows you to choose the number of 
seconds before the Held Line Reminder feature...

System prgrming / 423
P0603534  02Modular ICS 6.1 Installer Guide
Press CHANGE to select the setting: Y (Yes) or N (No).
Page tone
You can choose whether a tone sounds before a page begins.
Press CHANGE
 to select the setting: Y (Yes) or N (No).
Page Timeout
The paging feature is automatically disconnected after a set 
length of time. 
Press CHANGE
 to select the maximum number of seconds 
needed for a page: 15, 30, 60, 120, 180, 300, 600, 2700.
Daylight time
When this feature is turned on, your system...

424 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
Press CHANGE, to select the setting: Y (Yes) or N (No).
AutoTime&Date
You can program the Automatic Time&Date feature to enable 
the Norstar system to automatically update the time and date 
after a power failure.
Whenever the clock is out of sync by more than two minutes, 
as a result of a power failure or a loss of power, the first 
incoming call updates the clock automatically after two rings.
Note:  CLASS trunks are required for this...

System prgrming / 425
P0603534  02Modular ICS 6.1 Installer Guide
Call log space
Call log space programming customizes how log space is 
allocated to telephones in the system.
Reset all logs allows you to reallocate the Call log space 
equally to all telephones in your system.
1. Press YES
 and use the dialpad to enter the space allocation 
for the Call log at each telephone. 
You must use a three-digit number (for example, 020 to 
give each set 20 spaces).
2. Press YES
 to accept the settings and end...

426 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
example, by lifting the receiver off the telephone, and the 
moment that Norstar sends dialed digits or codes on the line.
Press CHANGE
 to select the setting: 200, 400, 600, 800, 
1000, 1200, 1400, 1600, 1800, or 2000 milliseconds. 
Link time
Link time allows you to specify the duration of a signal 
required to access a feature through a remote system. 
Press CHANGE
 to select the setting: 100, 200, 300, 400, 500, 
600, 700, 800, 900, or...

System prgrming / 427
P0603534  02Modular ICS 6.1 Installer Guide
AlarmSet
Alarm set allows you to assign a telephone on which alarm 
messages appear when a problem has been detected in the 
system. 
1. Use CHANGE
 and the dialpad to enter the internal number of 
the Alarm telephone. 
2. Press ‘ to set the Alarm telephone to None. 
The default setting is 221. 
Refer to “Alarm codes” on page 533 for details about reading 
alarms and troubleshooting with alarms.
Set relocation
Set relocation allows you to...

428 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
Msg reply enh
The Message reply enhancement feature allows for the 
message waiting indicator on analog telephones connected to 
an Analog Station Module (ASM) to be deactivated 
automatically if the reply call from the analog telephone to the 
designated direct-dial telephone is answered, no matter where 
the call is answered from by the user.
This feature also functions if the user invokes the Call Pickup 
feature to answer the reply...

System prgrming / 429
P0603534  02Modular ICS 6.1 Installer Guide
Answer key
Up to eight answer DNs can be assigned per telephone. The 
Answer key setting in Featr settings allows you to 
determine what types of calls will alert at the telephone for the 
Answer DNs assigned to any telephone. 
Answer key changes do not apply to portables.
Press CHANGE
 to select the settings: Basic, Enhanced, and 
Extended. 
On the Basic setting, answer keys do not ring for:
• Prime set call capture
• call forwarded...

430 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
but you still get calls to that number. To handle the calls, create 
an answer key using the phantom DN on the telephone where 
you want these calls to be taken.
Setting SWCA controls
You can assign up to 16 System Wide Call Appearance 
(SWCA) keys to each telephone in a group. This is performed 
under Button programming, located under 
Terminals&Sets, User Preferences. SWCA controls are 
controlled by feature codes ≤•fi¤‚
 to 
≤•fi‹fi. The...