Nortel Modular Ics 6.1 Installer Guide

System prgrming / 451
P0603534  02Modular ICS 6.1 Installer Guide
DN lengthInstaller password required
This feature allows you to change the number of digits for all 
DNs. The maximum length is seven. The default, and 
minimum length, is 3.
1. Press CHANGE
 to select the setting: 3, 4, 5, 6, or 7. 
2. Press  ‘ to save the new DN length. 
The display shows Drop data calls?.
3. Press YES
 to save the new DN length. 
NO
 restores the original value.
Tips - A DN length change, if required, should be the...

452 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
Nat’nl length (profile 2, only)Installer password required
This feature allows you to change the number of digits that the 
system will expect to see for a national telephone number.
1. Press CHANGE
 to select the setting: (default is 10). 
2. Press YES
 to save the new DN length. 
Make/Break (profile 2, only)Installer password required
This feature allows you to change the ratio of your system.
1. Press CHANGE
 to select the setting to...

System prgrming / 453
P0603534  02Modular ICS 6.1 Installer Guide
BusName
Norstar will display the name of the calling party when it is 
provided both Private or Public ISDN PRI and BRI interfaces. 
The displayed name may include information such as the 
Receiving Calling Name, Receiving Redirected Name, and/or 
Receiving Connected Name. The outgoing name is the 
business name concatenated with the set name. 
Network name display supported by protocol
Receiving and Sending Calling Party Name
Network name...

454 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
• The system supports sending the calling party name, which 
is the Business Name and Set Name concatenated together, 
on calls originated by the Norstar system.
For information about programming your Feature assignment, 
see Feature assignment (CLID alignment) on page 347.
The Set Name will only be sent if the OLI for the Set is 
configured. See OLI # on page 333.
Receiving and Sending Connected Name
Outgoing calls record the Connected...

System prgrming / 455
P0603534  02Modular ICS 6.1 Installer Guide
Programming Network Name Display
The Business Name and the Set Name make up the 
information that is used for the outgoing Calling name or 
connected name.
Calling/connected name is only sent once the Business Name 
is programmed. 
To program the Business Name, start with the display showing 
System prgming.
1. Press ≠.The display shows Hunt groups. 
2. Press ‘ until the display shows BusName:. 
3. Press CHANGE
 and use the keypad to enter...

456 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
Outgoing Name and Number Blocking
When activated, ≤°⁄· blocks the outgoing name and 
number on a per call basis. When this feature is used, the call 
is flagged to the CO so that the name and number will not be 
presented to the person being called.
On analog and BRI trunks, a call blocking digit sequence is 
sent to the CO before sending the dialout digits. You can 
change this digit in a Norstar programming session and set it 
to the...

System prgrming / 457
P0603534  02Modular ICS 6.1 Installer Guide
Call by Call service selection for 
PRI
Installer password required
Call by Call service selection allows a user to access services 
or private facilities over a PRI line without the need for 
dedicated facilities. The different services represent different 
types of access to the network. Various services are available 
depending on the chosen protocol. The list below identifies the 
supported services
Call by Call service selection is...

458 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
OUTWATS
(Outward 
Wide Area 
Telecommu-
nications)This outgoing call service allows a Norstar 
user to call telephones in a specific geo-
graphical area referred to as a zone or band. 
Typically a flat monthly fee is charged for 
this service.
INWATS 
(Inward 
Wide Area 
Telecommu-
nications)This long distance service allows a Norstar 
user to receive calls originating from speci-
fied areas without charge to the caller. A toll-
free...

System prgrming / 459
P0603534  02Modular ICS 6.1 Installer Guide
Norstar supported Call by Call Services by protocol
a.  A shaded box indicates that the protocol does not support the service.
b.  DMS-250 Sprint and UCS support incoming FX only (i.e. Network-to-
Norstar). DMS-250 MCI does not support FX.
c.  NI-2 allows two Tie operating modes: senderized and cut-through. Norstar 
will only support senderized mode.
d.  Rates greater than 64 kbps will not be supported.
e.  Bell Canada VNET.
f.   Not all...

460 / System prgrming
Modular ICS 6.1 Installer GuideP0603534  02
Line Pools
All lines in a PRI interface are in the same PRI line pool. This 
pool cannot contain any non-PRI lines. There is one PRI pool 
available for each PRI interface on the CSU. 
Depending on the order that the cards are configured as PRI, 
Pool PRI-A represents lines 1 to 30, and Pool PRI-B represents 
lines 31 to 60. If both PRIs are connected to the same service 
provider and use the same protocol, lines 1 to 30 and 31 to 60 
can...