Nortel Compact Ics 6.1 Installer Guide

Installing ISDN terminal equipment / 111
P0603539  02Compact ICS 6.1 Installer Guide
No power supply is provided for the U-LT wiring. If equipment attached to 
the U-LT loop requires optional power, install an approved power supply 
unit. See ANSI T1.601-1992 Annex H or the documentation that comes 
with your TE for more information.
Jack and plug pin numbering     
8  7  6  5  4  3  2  1
1       2      3       4       5       6     7       8    

112 / Installing optional equipment
Compact ICS 6.1 Installer GuideP0603539  02
Installing optional equipment
Auxiliary ringer (customer supplied)
The Norstar ICS provides a control contact to operate an auxiliary ringer. 
1. Follow the manufacturer’s installation instructions.
2. Connect the auxiliary  ring generator to  the 25-pair distribution block 
as shown in the wiring charts. The pins in the chart provide a control 
contact. They do not provide ring current or dc voltage. The contact is 
capable...

Installing optional equipment / 113
P0603539  02Compact ICS 6.1 Installer Guide
External music source programming
Music for callers on Hold and for Background Music must be enabled 
through programming. Refer to the Programming chapter for more details. 
Refer specifically to the following Programming headings and confirm that 
the following settings are implemented:
External paging system (customer supplied)
You can connect an external paging system to provide paging over external 
loudspeakers. The...

114 / Installing optional equipment
Compact ICS 6.1 Installer GuideP0603539  02
 
Tip - Norstar external paging does not support 
talk-back paging equipment unless an external line 
port is used.
The Norstar system provides paging over the 
Norstar telephone speakers, even when no 
external paging equipment is connected.
Install all optional equipment before powering up 
the system. 

Powering up the system / 115
P0603539  02Compact ICS 6.1 Installer Guide
Powering up the system 
1. Ensure the filler faceplates (slot covers) are in place.
2. Make sure the air flows freely around the unit and that nothing is 
sitting on or blocking the area around it. The gap between the ICS and 
the backboard must be left completely clear.
3. Double-check all wiring. Do not connect the central office and station 
lines prior to connecting power.
4. Connect the power cord to an electrical outlet...

116 / Powering up the system
Compact ICS 6.1 Installer GuideP0603539  02
Replacing the cover 
Once the system is initialized and the telephone displays shows 
Jan 1 1:00 
am
, you have 15 minutes in which to perform Startup programming. Refer 
to Startup programming on page 136. After 15 minutes, access to Startup 
programming is denied. You can turn the system power off and back on if 
you need to access Startup programming after this point.
Call Log information may be lost.
If the Norstar system...

P0603539  02Compact ICS 6.1 Installer Guide
Programming
The installer or the customer service representative programs settings for 
the entire Norstar system, plus settings for individual telephones and 
external lines. Most of the settings can also be programmed by a system 
coordinator who has a plus (SysCoord+) password.
Programming overview
Programming access is controlled by these passwords. 
Profile password — allows you to determine the system profile. The 
default profile is the profile used for...

118 / Programming
Compact ICS 6.1 Installer GuideP0603539  02
For more information about programming using the System Coordinator 
and Basic passwords, see the Compact ICS 6.1 System Coordinator Guide.
Profile, Dialpad and Startup programming
Profile: ²¥¥¸å¯ìéñä(**7763453)
Dialpad: 
(**3425723)
Startup: 
(**7827887)
Default password: 
‚¯öìéí (266344)
ProfileDialpadStartup
Password: 
(CONFIG)
Password: 
(CONFIG)Reset Memory?
YES
Region: PROF1
OK       CHANGE
QZ:0
              CHANGETemplate:...

Programming / 119
P0603539  02Compact ICS 6.1 Installer Guide
Installer or System Coordinator Plus 
programming
Entry code: ²¥¥‚¯öìéí(**266344)
Installer password: ‚¯öìéí (266344)
System Coordinator Plus password: 
ꂸñèê
(727587)
Programming using the Installer and System Coordinator Plus 
password
StartupPasswordsNetwork Services
TemplateCOS pswdsRelease reasons
Start DNCall log pswdsTelco features
Terminals&SetsProgrming pswdsVMsg ctr tel#s
Line accessIRAD pswdSoftware Keys
CapabilitiesSM PasswdSysID...

120 / Programming
Compact ICS 6.1 Installer GuideP0603539  02
Shaded items are seen only if you are using the Installer password. Settings 
that require an Installer password are identified with a special icon in the 
programming instructions.
The Auto Reporting subheading will not appear unless your Feature 
Cartridge comes with remote administration enabled, or you have enabled 
the feature using software keys.
System Coordinator programming
Entry code: ²¥¥‚¯öìéí(**266344)
Default System Coordinator...