Nortel Compact Ics 6.1 Installer Guide

Installing the cartridges / 81
P0603539  02Compact ICS 6.1 Installer Guide
Installing Trunk Cartridges   
1. Slide the Trunk Cartridge into slot 1, applying equal pressure at the top 
and bottom. See illustration on the next page.
2. Close the cartridge clips at the same time, to keep the cartridge aligned 
with the connector.
3. If you are installing a second trunk cartridge, remove the filler 
faceplate from slot 2 and slot 3 (it is one piece), using a screwdriver at 
the bottom of each slot and prying...

82 / Installing the cartridges
Compact ICS 6.1 Installer GuideP0603539  02
11100000*Sweden
00010000*South America
10010000*Brazil
01010000*Norway
11010000*France
00110000*Germany
10110000*Korea
XXXXXXX1*Reserved
XXXXXX1X*Reserved
XXXXX1XX*Reserved
* Reserved for future development
DIP switch settingCountry profile 

Installing the cartridges / 83
P0603539  02Compact ICS 6.1 Installer Guide
               

84 / Installing the cartridges
Compact ICS 6.1 Installer GuideP0603539  02
Installing the Expansion Cartridge   
The Expansion Cartridge must be equipped with clock control if you are 
installing BRI Cards.
1. Remove the filler faceplate from slot 3 (and slot 2 if there is no Trunk 
Cartridge), using a screwdriver to pry the bottom edge(s)  out.
2. If required, snap the two parts of the faceplate apart and put back the 
filler faceplate in slot 2.
3. Slide the Expansion Cartridge into slot 3, applying...

Installing the cartridges / 85
P0603539  02Compact ICS 6.1 Installer Guide
  
 
Removing the expansion cartridge will cause 
a cold restart.
If you downsize the system by removing the 
expansion cartridge, all system programming will 
be lost.
Alarm Telephone will indicate a cold reset.
An alarm and a prompt indicating warm or cold 
reset will occur on the alarm telephone when the 
system size has been decreased.  

86 / Installing the cartridges
Compact ICS 6.1 Installer GuideP0603539  02
Installing the Expansion Cartridge 

Connecting the wiring / 87
P0603539  02Compact ICS 6.1 Installer Guide
Connecting the wiring
Connecting the wiring for a Compact ICS
Extend 150 mm (6 in.) 
and clamp before bringing
cables together.
Do not attach central office
or station line connections until
power is connected to the ICS. 

88 / Connecting the wiring
Compact ICS 6.1 Installer GuideP0603539  02
Connecting the wiring to the distribution panel
1. Route the cables from the ICS to the distribution panel.
2. Bundle the cables with cable ties and secure them to the wall to support 
their weight.
3. Connect the telephone and auxiliary equipment wires to the 
appropriate pins on the distribution block (refer to the wiring charts).
4. Cross-connect the ICS telephone and auxiliary equipment wiring to 
the corresponding station pins on...

Connecting the wiring / 89
P0603539  02Compact ICS 6.1 Installer Guide
B1 and B2 directory numbers (DNs)
Norstar has a B1 and B2 channel for transmitting voice and data. Each 
telephone port on the ICS has a B1 DN and a B2 DN. Devices such as the 
Business Series Terminals, and Norstar telephones use only the B1 DN. 
Other devices may need both B1 and B2 channels, therefore, requiring B1 
and B2 DNs.
Norstar Compact ICS uses different numbering schemes for the B1 and B2 
DNs, depending on how you upgrade...

90 / Connecting the wiring
Compact ICS 6.1 Installer GuideP0603539  02
ICS numbering (restricted feature cartridge, expanded): 
Expansion Cartridge added 
ICS numbering (standard feature cartridge)  
ICS numbering (standard feature cartridge): Expansion 
Cartridge added at installation  
ICS numbering (standard feature cartridge): Expansion 
Cartridge added later  
Connector 
#DevicePortsB1 DNB2 DN
ICS (#1)Telephones 1-8
I-ATA
I-RAD
Telephones 9-16
Telephones17-24101-108
117
118
109-116
119-12621-28
29...