Norstar Compact 616 Dr5 Installer Guide

Page zone
Each telephone can be assigned to one of three zones for
receiving Page messages. A zone is any selection of 
telephones you want to group together, regardless of location.
Use the 
 display button to select the setting: 1, 2, 3,
  
      
You can program Page  only if the telephone has Paging set
to Yes.
Auxiliary   
This setting causes the Auxiliary Ringer (if installed) to ring when
the telephone rings. An Auxiliary Ringer is important in noisy
environments where a 
 telephone might...

44  Capabilities
Call Forward No Answer
Call Forward No Answer lets you redirect an incoming call to
another telephone on your  system when the call is not
answered at your telephone.”  
Use the  button, the  display button, and the
dial pad to program the. internal number of the telephone that
your calls are to be directed to.’
  
 Answer delay
If you assign another telephone to receive your calls, you can
also assign the number of times that the incoming call rings
before the call is forwarded. To...

Capabilities  
 you select  , use the [Show] button, the 
display button, and the dial pad to program the external
telephone number that Hotline calls are to be directed to, and to
program the line Hotline calls are to be made on.
 
Programming hints
The  should,  labeled to inform anyone using it that
Hotline is active. 
A telephone’s Prime fine, line pool access codes, and access to a
line pool can be programmed by your Customer Service
representative.
 Priority Call
This feature lets you call from...

46  Capabilities
A Class of Service can be associated with a telephone, a line or
a COS password. It determines the dialing capabilities that apply
to internal telephones and any lines used for external calls.
Users have a Class of Service associated with their telephones,
in the sense that there are dialing filters associated with
telephones, as  line  assignments. Use of a COS
password affects only the telephone’s dialing capabilities.
The ability to change the COS internally means that someone
using...

User filter
The COS User filter replaces the telephone (set) fiiter or the
line/set filter that would otherwise apply to a specific call.
Use the  button, the  display button, and the
dial pad to program the two-digit User filter. The default setting
  means that any other filters in place (telephone (set)
 filter or line/set filter) still apply,
Line filter
The COS Line filter replaces the line filter that would otherwise
apply to a specific call.
Use the  display button, and the dial pad to program...

48  Service Modes
Service Modes
Using Service Modes, you can control how the  system
responds to calls, depending on the time of day. Up to three
different Service Modes can be programmed, each with unique
ringing arrangements.
5. CapabilitiesII
6. Service ModesControl telephones
Name
7. PasswordSetting
Trunk Answer
8.  DefaultsExtra-Dial
   Ringing telephones
Aux ringerJ
Control telephones
Control telephones are assigned to each external line and are
used to control the Service Mode by allowing you to...

You can assign a Control telephone to more than one external
line, but a line cannot be assigned to more than one Control
telephone.
Only one Service Mode applies at any one time to all external
lines controlled
by a given Control telephone.
The default Control  for all  is 21.
Service Modes
The three Service Modes are programmed in the same way.
Service Mode Name
The Service Mode Name identifies the active Service Mode, and
is shown on the display of the Control telephone when the
 Mode is turned ON....

50  Service Modes
Manual allows you to turn the Service Mode ON and OFF at any
time from a Control telephone. The Service Modes feature code
must be entered at the telephone to access this feature.
.Automatic allows you to pre-assign a stop and start time during
which the Service Mode is active. You are still able to start and
stop the Service Mode by entering the Service Modes feature
code at a Control telephone. If you  setting, you will
have to program start and stop times. See the section in this...

   
Trunk Answer
Trunk Answer allows you to answer, from any telephone, an
external call which is ringing at another telephone in your office.
This is useful if the other telephones have not been assigned the
same lines as the telephone you are using to answer the call.
 You can change the Trunk Answer setting only if the Service
Mode is set to Manual or Automatic.
Use the  display button to select the setting: Y (Yes) or
N (No).  
Extra-Dial telephone
A telephone normally in service as a Direct-Dial...

52  Password
Password
The Administration password allows access to Administration
programming. This prevents unauthorized or unintentional
changes to  To ensure security, distribute the passworhs
only to selected 
 keep a record of your password in a
secure place, and change the password periodically.
The password is a one to six-digit number. The default
Administration password is      which is the same as
Use the [Show] button, the  display button and the
dial pad to enter the new Administration...