Nitsuko Digital System Feature And Terminal Programming Manual

CP- SINGLE RING OPX (BY2:7)
Description
Use this option to enable (0) or disable (1) Distinctive Ringing for ports with circuit types 05 and 51 (OPX and
ASI extensions). If enabled (0), trunk calls have two short rings (repeated) followed by a pause.  Intercom calls
have a single one second ring followed by a pause.  If disabled (1), Intercom and trunk calls have a single one
second ring followed by a pause.
In  
>AUX Y2.1/Base Y5.1, use this option to control the types of calls Voice Mail Personal...

CP- INHIBIT FLASH FOR SINGLE LINE TELEPHONES (BY2:6)
Description
Use this option to enable (0) or disable (1) Flash for ESL sets with this COS.  If enabled, ESL users can press
and release the hookswitch to Flash a trunk.
Note:
If you are using BY2:6 to assign an ACD supervisor keyset, go to CP- ACD Supervisor Keyset (BY2:6) on the
next page.
Conditions
None
Default Value
Flash allowed at ESL sets (0).
Feature Reference
Flash
Instructions
To enter data on the PRF:
1. On Table 2 for BY2:6, enter 0 allow...

CP- ACD SUPERVISOR KEYSET (BY2:6)
Description
Use this option to assign extensions with this COS as ACD supervisor keysets.  This option only identifies the
extension as a supervisor.  It does not assign the keyset to an ACD group (see Related Programming below).  If
enabled (1), extension is an ACD supervisor.  If disabled (0), extension is not a supervisor.
Conditions 
None
Default Value
ACD supervisor not assigned (0).
Feature Reference
Automatic Call Distribution
Instructions
To enter data on the...

CP- ALLOW SILENT MONITOR (BY2:5)
Description
Use this option to allow (1) or prevent (0) Silent with this COS from initiating Silent Monitor.
Conditions 
None
Default Value
Silent Monitor not allowed (0).
Feature Reference
Silent Monitor
Instructions
To enter data on the PRF:
1. On Table 2 for BY2:5, enter 0 to prevent extensions from initiating Silent Monitor.  Enter 1 to allow ex-
tensions to initiate Silent Monitor.
To enter data at the programming terminal:
1. Type CP.  You see: COS # 00: 00010000...

CP- INHIBIT ACCESS TO PAGE ZONE 3 (BY2:4)
Description
Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting announcements into Paging
zone 3.  This option also applies to DISA trunks.
Conditions 
None
Default Value
Access to Page Zone 3 allowed (0).
Feature Reference
Paging
Tenant Service
Instructions
To enter data on the PRF:
1. On Table 2 for BY2:4, enter 0 to allow extensions Paging into zone 3.  Enter 1 to restrict extensions from
Paging into zone 3.
To enter data at...

CP- INHIBIT ACCESS TO PAGE ZONE 2 (BY2:3)
Description
Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting announcements into Pag-
ing zone 2.  This option also applies to DISA trunks.
Conditions 
None
Default Value
Access to Paging zone 2 allowed.
Feature Reference
Paging
Tenant Service
Instructions
To enter data on the PRF:
1. On Table 2 for BY2:3, enter 0 to allow extensions Paging into zone 2.  Enter 1 to restrict extensions from
Paging into zone 2.
To enter data at...

CP- INHIBIT ACCESS TO PAGE ZONE 1 (BY2:2)
Description
Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting announcements into Paging
zone 1.  This option also applies to DISA trunks. 
Conditions 
None
Default Value
Access to Paging zone 1 allowed.
Feature Reference
Paging
Tenant Service
CP- INHIBIT ACCESS TO PAGE ZONE 1 (BY2:2)
Instructions
To enter data on the PRF:
1. On Table 2 for BY2:2, enter 0 to allow extensions Paging into zone 1.  Enter 1 to restrict extensions...

CP- INHIBIT ACCESS TO ALL CALL PAGING (BY2:1)
Description
Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting All Call Paging an-
nouncements.  This option also applies to DISA trunks.
Conditions 
None
Default Value
Access to All Call Paging allowed.
Feature Reference
Paging
Tenant Service
Instructions
To enter data on the PRF:
1. On Table 2 for BY2:1, enter 0 to allow extensions All Call Paging.  Enter 1 to restrict extensions from
All Call Paging.
To enter data at the...

CP- DIRECT TRUNK ACCESS AND TRUNK CAMP-ON (BY2:0)
Description
Use this option to enable (1) or disable (0) Direct Trunk Access for extensions with this COS.  If allowed, exten-
sions can also use Forced Trunk Disconnect.  Additionally, extensions with Direct Trunk Access capability can
dial 2 to Camp-On to a busy trunk.  This option also allows extensions to program System Speed Dial numbers.
Conditions 
None
Default Value
•Direct Trunk Access allowed (1) for COS 0.
•Direct Trunk Access not allowed (0)...

D- DISPLAY MEMORY
Description
This program displays the contents of system memory locations. It is a factory diagnostic tool, not intended for
field use. Consult your Field Service representative for more information.
Conditions 
None
Default Value
None
Feature Reference
System Reports, Diagnostics and Maintenance Utilities
Instructions
None
D- DISPLAY MEMORY
N1870SWG04   Issue 1-0 PROGRAMMING   333