Nitsuko Digital System Feature And Terminal Programming Manual

AP- SIX DIGIT ANALYSIS
Description
Use this option to enable/disable six-digit translation.  With six-digit translation, the system restricts a call ac-
cording to the NPA and the NNX the user dials.  If six-digit translation is allowed, the system compares the NPA
and NNX code the user dials to the programmed six-digit list.  For each area code, the list can be either an allow
or deny list.  This means the list can either selectively allow or deny the dialed codes.  For each toll level, the
system...

 
From this menu Type this Function To use these options
AP-CMD>Enter
ADisplay list of options.
Add a code to the list.
Enter
Enter NNX code (3-digits) from Table 1. The
system then asks for your next entry.
After making all your entries, press ENTER 
to go back to AP-CMD> options for 
this list.
D
Delete a code from 
the list.
Enter
Enter NNX code (3-digits) from Table 1. The
system then asks for your next entry.
After making all your entries, press ENTER 
to go back to AP-CMD> options for 
this list....

AP- TOLL RESTRICTION EXAMPLE
The following is a Toll Restriction example for a sample corporation located in NPA (area code) 203.  This ex-
ample illustrates one solution to sample corporation’s Toll Restriction requirements.  For simplicity, the example
is limited to toll level 2.  A completed Program Record Form for sample corporation is shown on the following
two pages.
For this requirement... Use this programming
Toll level 2 For Toll Level, enter 2
No continued dialing For Allow Active Dial Pad,...

 
Table 1 PROGRAM RECORD FORM, TOLL RESTRICTION (Page 1 of 3)
01850I1
SAMPLE
ENTER TOLL LEVEL
ACTIVE DIAL PAD?
ALLOW SPECIAL ACCESS (N11) DIALING?
ALLOW 0+ DIALING?
ALLOW DIRECT INTL DIALING?
ALLOW EQUAL ACCESS?
ALLOW OR DENY TABLE?
DATA
ALLOW 1+NNX DIALING?
ALLOW OR DENY TABLE?
DATA
ALLOW NNX DIALING?
ALLOW OR DENY TABLE?
DATA
ALLOW NPA DIALING?
ALLOW OR DENY TABLE?
DATA[1-7]
[Y/N]
[Y/N]
[Y/N]
[Y/N]
[Y/N]
[A/D]
[000-999, XXX]
[Y/N]
[A/D]
[200-999, XXX]
[Y/N]
[A/D]
[200-999, XXX]
[Y/N]
[A/D]
[200-919,...

 
X     X     X
D 7     1     8
Y
2     1     2
Table 1 PROGRAM RECORD FORM, TOLL RESTRICTION (Page 2 of 3)
01850I2
SAMPLE
SIX DIGIT ANALYSIS?
AREA CODE
ALLOW OR DENY TABLE?
DATA
AREA CODE
ALLOW OR DENY TABLE?
DATA
AREA CODE
ALLOW OR DENY TABLE?
DATA
AREA CODE
ALLOW OR DENY TABLE?
DATA
[200-999, XXX] [Y/N]
[A/D][200-919, XXX]
[200-919, XXX]
[A/D]
[200-999, XXX]
[200-919, XXX]
[A/D]
[200-999, XXX]
[200-919, XXX]
[A/D]
[200-999, XXX]
A
D
7     X     X
6     8     8 5     6     X5     4     7
7     X     X...

C- CLASS OF SERVICECL- LIST COS
Description
Use this option to list the programmed Class of Service.
Conditions 
None
Default Value
•All extensions have COS 01.
•The attendant has COS 30.
•See chart below for details.
•Data Ports with Permanent Receive/Transmit Connection have COS 29.  Refer to the Data Products Man-
ual.
Feature COS Option Byte/BitCOS 1
Default
Automatic Call Distribution ACD Supervisor Keyset BY2:6 0-No
Call Forwarding Inhibit Call Forwarding BY0:6 0-No
Call Waiting Allow Off-Premise...

Feature Reference
System Reports, Diagnostics and Maintenance Utilities
Instructions
To enter data on the PRF:
No entry required.
To enter data at the programming terminal:
1. Press CL.  The Class of Service listing displays.  See below for a partial display.
COS CONFIGURATION
     ****    ****    ****    ****
BYn: BIT7   BIT6   BIT5   BIT4
     BIT3   BIT2   BIT1   BIT0
BY0: INH SYS SPEED DIAL   INH CALL FWD    INH CAMP ON    BREAK-IN
     OFF-P CFWD           ICM NITE ONLY   ABSORB/INH OPA BELL CAS...

CP- INHIBIT SYSTEM SPEED DIAL (BY0:7)
Description
Use this option to allow (0) or deny (1) extensions with this COS the ability to use System Speed Dial.  This op-
tion also restricts System Speed Dial for DISA trunks.
Conditions 
This option does not apply to CO trunks.
Default Value
System Speed Dial enabled (0).
Feature Reference
Speed Dial
Instructions
To enter data on the PRF:
1. On Table 2 for BY0:7, enter 0 to enable System Speed Dial for each COS.  Enter 1 to disable System
Speed Dial.
To enter...

CP- INHIBIT CALL FORWARDING (BY0:6)
Description
Use this option to allow (0) or deny (1) on-premise Call Forwarding for extensions with this COS.  For system
attendants (in COS 00), use this option to allow/deny the Alternate Attendant and Removing Trunks and Exten-
sions From Service features.
Conditions 
None
Default Value
Call Forwarding and Alternate Attendant enabled (0).
Feature Reference
Alternate Attendant
Call Forwarding
Removing Trunks and Extensions From Service
Instructions
To enter data on...

CP- INHIBIT CAMP-ON (BY0:5)
Description
Use this option to allow (0) or deny (1) a user’s ability to send Call Waiting (Camp-On) tones to a busy exten-
sion by dialing 2.  (To allow/deny a user’s ability to Camp-On to a busy trunk, refer to BY2:0.)
Conditions 
None
Default Value
Camp-On to extensions allowed (0).
Feature Reference
Call Waiting (Camp-On)
Instructions
To enter data on the PRF:
1. On Table 2 for BY0:5, enter 0 to enable Camp-On for each COS. Enter 1 to disable Camp-On.
To enter data at the...