Nitsuko Digital System Feature And Terminal Programming Manual

— For Your Notes —
D- DISPLAY MEMORY
334   PROGRAMMING N1870SWG04   Issue 1-0 

E- EXTENSIONS E0- ALL EXTENSION DATA
Description
Use E0 to enter data for all options sequentially for an extension.  The charts below show the E options that cor-
respond to each E0 entry.  Refer to these options for more information. Also, the charts below show the default
value for each option (where applicable).
E0 Prompts for Keysets
For this option... Look here...
EXT
PORTE1
CIRCUIT TYPE- E2
COS (30 for Attendant, 01 for phones)- E3
NEXT EXT IN HUNT- E4
HUNT TYPE 00- E5
DATA SET OR DATA MODULE? N...

E0 Prompts for ESL Sets
For this option... Look here...
EXT
PORTE1
CIRCUIT TYPE 00- E2
COS 00 -E3
NEXT EXT IN HUNT    - E4
HUNT TYPE 00- E5
PAGE ZONE 00- E7
ALLOW LINE DIAL-UP Y [Y/N] -  E8
ACCESS TO GROUP 90? Y [Y/N] -  E8
     through
ACCESS TO GROUP 95? Y [Y/N] -  E8
DIR TERM OR OPR EXT 300- E9
UCD MASTER EXT    - EA
SPD DIAL BLOCK EB
CALL PICKUP GROUP 00- EC
ACCESS CONTROL ED
COPY? [SKIP=] [Y/N] - 
LINES  1 TO  8  Y Y Y Y  Y Y Y Y  -
                through
      65 TO 72  Y Y Y Y  Y Y Y Y  -...

E0 Prompts for ASI/OPX Sets
For this option... Look here...
EXT
PORTE1
CIRCUIT TYPE  E2
COS 00 -E3
NEXT EXT IN HUNT    - E4
HUNT TYPE 00- E5
ALLOW LINE DIAL-UP Y [Y/N] -  E8
ACCESS TO GROUP 90? Y [Y/N] -  E8
        through
ACCESS TO GROUP 95? Y [Y/N] -  E8
DIR TERM OR OPR EXT 300- E9
UCD MASTER EXT    - EA
SPD DIAL BLOCK EB
CALL PICKUP GROUP 00- EC
ACCESS CONTROL ED
COPY? [SKIP=] [Y/N] - 
LINES  1 TO  8  Y Y Y Y  Y Y Y Y  -
                through
      65 TO 72  Y Y Y Y  Y Y Y Y  -
CALL-OUT CONTROL ED...

E0 Prompts for Data Ports and Data Modules
For this option... Look here...
EXT
PORTE1
CIRCUIT TYPE (01=Data Module, Z=Data Port) E2
DATA MODULE [Y]/DATA PORT [N] Y-(Data Port Only) E2
COS 01 -E3
NEXT EXT IN HUNT    - E4
HUNT TYPE 00- E5
DATA SET OR DATA MODULE? [Y/N] 
  (Y=Data Module, N=Data Port)  E6
PAGE ZONE 00- E7
RING-LINE PREFERENCE? N [Y/N] - E8
OFF-HOOK RINGING? N [Y/N] -  E8
KEY ACCESS TO OUTBOUND LINES Y [Y/N] -  E8
ALLOW LINE DIAL-UP Y [Y/N] -  E8
ACCESS TO GROUP 90? Y [Y/N] -  E8...

E0 Prompts for Data Ports and Data Modules (Cont’d)
For this option... Look here...
(Data Module and Data Port only)
DATA MODULE BAUD RATES EM
  0-SLAVE,1-300,2-1200,3-1800
  4-2400,5-4800,6-9600,7-19200
  0 - 
DATA MODULE PARITY OPTIONS EM
  0-NO PARITY 8 BITS,1-EVEN 7 BITS,2-ODD 7 BITS
  0 - 
INTERACTIVE MODE? N -  EM
INTERACTIVE ECHO? N - EM
RS232 CONTROLS ACTIVE? N -  EM
ALLOW DTR DISCONNECT? N -  EM
ALLOW BREAK DISCONNECT? N -  EM
AUTO BAUD? N -  EM
BUSY ON DTR LOW? N -  EM
E0 Prompts for Modem...

Feature Reference
Refer to the individual E options.
Instructions
To enter data on the PRF:
1. Refer to the individual E options.
To enter data at the programming terminal:
1. Type E0.
2. Press RETURN to program extension 300.
OR
Enter another extension number and press RETURN. In either case, you see: PORT
3. Enter data for the E options from Table 3. 
After you enter data for one option, you automatically advance to the next option.
You cannot use E0 to enter data for the EY and EZ options.
E-...

E1- EXTENSION PORT NUMBER
Description
Use this option to change the port assignment for an extension. The port is the hardware location of the exten-
sion.  When you change an extension’s port number, all programming for the extension goes to the new port as-
signment (location).
All extensions use a single port, except for DSS Consoles.  This is a dual-port device that use a port pair.  A port
pair consists of two consecutive ports, beginning with an even numbered port (e.g., 00 and 01).  When changing...

E2- EXTENSION CIRCUIT TYPE
Description
Use this option to identify the type of telephone connected to each extension port.  The extension circuit type
choices are:
•00 ESL set
•01 Keyset (without display) and Data Module (refer to the Data Products Manual)
•02 Display keyset
•06 DSS Console
•51 Dual ASI with DTMF receiver (P/N 89749)
•52 Digital Voice Mail Port Card
•M Modem Pooling port (refer to the Data Products Manual)
•Z Data Port and data-only Data Module (refer to the Data Products Manual)
•X...

Off-Premise Extension (OPX)
Peripheral Control Unit (PCU) Module
Private Line
Telemarketing Dial
Voice Mail Compatibility (Integrated Voice Messaging)
Instructions
To enter data on the PRF:
1. Enter the circuit type for each extension on Table 3.
To enter data at the programming terminal:
1. Type E2.  You see:  EXT 300
2. Press RETURN to program extension 300
OR
Enter another extension number and press RETURN. In either case, you see: CIRCUIT TYPE
3. Enter data for this option from Table 3 and press...