Nitsuko Digital System Feature And Terminal Programming Manual

 
TYPE OF CALL
Transfered
  trunk
01850C42 (S)
EXTENSION HUNTING OPERATIONAL MATRIX (Page 5 of 6)
CONDITION UDC 04 UDC 05 UDC 06
Direct term.
  trunk
Intercom
Skip member. If all busy,
Camp-On for 1st free
member, then overflow,
then Key Ring. Busy Skip member. If all busy,
Pls hold msg, Camp-On 
for 1st free member, then 
overflow, then Key Ring.
Cycles UCD group queue.
N/A N/A N/A Ring - No answer
Voice call - No answer
Treat as busy. D.N.D.
Call ForwardedSkip member. If all busy,
Pls hold msg, Camp-On...

 
TYPE OF CALL
DID
01850C43 (S)
EXTENSION HUNTING OPERATIONAL MATRIX (Page 6 of 6)
CONDITION UDC 04 UDC 05 UDC 06
DISASkip member. If all 
busy, busy tone. Busy
N/A N/A N/A Ring - No answer
Voice call - No answer
D.N.D.
Call Forwarded
Tie lineSkip member. If all 
busy, Pls hold msg, 
then overflow.
UCD NOTES:
Overflow and Key Ring - If no overflow extensions are programmed, call will stay Camped-On.
Abbreviated voice synthesized messages are shown in quotes; e.g. Pls hold
 is actually Please hold on. All...

Feature Reference
Automatic Call Distribution
Extension Hunting
Voice Mail Compatibility (Integrated Voice Messaging)
Instructions
To enter data on the PRF:
1. Enter the hunt type 01-06 for each extension on Table 3.  Enter 00 if the extension in not in a hunt group.
To enter data at the programming terminal:
1. Type E3.  You see:  EXT 300
2. Press RETURN to program extension 300.
OR
Enter another extension number and press RETURN.  In either case, you see: HUNT TYPE
3. Enter data for this option from...

E6- DATA SET
Description
Use this option to assign a  Data Module with a bridged keyset.  For extensions that are not bridged to Data
Modules, always disable this option.  When programming Data Modules, refer to the Data Products Manual.
This option applies to keysets only.
Conditions 
None
Default Value
Extension is not a keyset bridged to a Data Module (N).
Feature Reference
Refer to the Data Products Manual
Instructions
To enter data on the PRF:
1. On Table 3, enter Y for each extension that is a...

E7- PAGE ZONE
Description
Use this option to assign a keyset or ESL set to an Internal Paging zone.  The internal zones are:
•00 All Call Paging only
•01 Internal zone 1
•02 Internal zone 2
•03 Internal zone 3
•04 Internal zone 4
•05 Internal zone 5
•06 Internal zone 6
•07 Internal zone 7
For example, you can assign extension 304 to internal zone 5 (05).  The speaker in extension 304 only broad-
casts zone 5 and All Call Paging announcements.
Conditions 
None
Default Value
Extension broadcast All Call...

E8- LINE ACCESS OPTIONS, RINGING LINE PREFERENCE
Description
Use this option to allow or deny Ringing Line Preference at each keyset. This option applies to all trunk calls
ringing the extension (not Intercom calls).
Conditions 
Intercom calls to an attendant follow E8- Ringing Line Preference programming.
Default Value
Ringing Line Preference disabled (N).
Feature Reference
Ringing Line Preference
Instructions
To enter data on the PRF:
1. Enter Y for each extension on Table 3 that should have Ringing...

E8- LINE ACCESS OPTIONS, OFF-HOOK RINGING
Description
Use this option to enable/disable incoming off-hook ring for a keyset.  Keep in mind that this option interacts
with EF- Incoming Whisper Page Off-Hook Signals.  The chart below shows this interaction for the destination
extension.
Caller Dest. E8 EF Result after dialing 1
Handset
Handset
Handsfree
and MonitorHandset
Handsfree
Handset
HandsfreeN
N
N
NN
N
N
NWhisper Page to destination
No Off-Hook Signaling
No Off-Hook Signaling
No Off-Hook Signaling...

E8- LINE ACCESS OPTIONS, KEY ACCESS TO OUTBOUND LINES
Description
Use this option to allow/deny a keyset user programmable line key access to outside trunks.  If enabled, a keyset
user can press a line key to place a call (if also allowed by the Related Programming below).  If disabled, user
cannot use line keys for placing outside calls.  This option applies to all line keys on the keyset.  Additionally, it
does not affect dial access to trunks and trunk groups.
This option also lets:
•A user with Prime...

E8- LINE ACCESS OPTIONS, ALLOW LINE CODE DIAL-UP
Description
Use this option to allow/deny an extension user from dialing a trunk code (e.g., 801) for an outside call.  This op-
tion affects all trunk codes.  It does not affect and extension user’s capability to:
•Dial a trunk extension number (e.g. 500)
•Dial a trunk group code (e.g., 90)
•Press a line key for an outgoing call
This option also applies to DISA trunks.
Conditions 
This option does not apply to DSS Consoles and Modem Pooling ports.
Default...

E- EXTENSIONS (HYBRID ONLY) E8- LINE ACCESS OPTIONS, ACCESS TO GROUPS 90-95
Description
Use this option to allow/deny an extension dial access to the first six trunk groups (90-95).  If enabled, an exten-
sion user can dial a trunk group code (90-95) to place an outside call on one of the first six groups.  If disabled,
the user cannot dial the trunk group code for groups 90-95.  This option does not affect:
•Dial access to groups 96-98
•Dial access using trunk codes (e.g., 801)
•Dial access using trunk...