Nitsuko Digital System Feature And Terminal Programming Manual

WALKING CLASS OF SERVICE
Description
Walking Class of Service lets an extension user temporarily override Class of Service dialing restrictions.  This helps
a user that must place an important call while at a co-worker’s phone.  Walking Class of Service lets the user:
•Go to a co-worker’s phone
•Implement Walking Class of Service
•Place an outside call that the extension normally restricts
Walking Class of Service overrides the following CP- Program COS restrictions (refer to the Class of Service...

Feature Operation
To use Walking Class of Service to place an outside call:
1. Lift handset.
2. Press ICM.
Listen for: Dial Tone
If you have an ESL set, skip this step.
3. Press # twice.
Listen for: Dial tone stops
4. Dial Walking Class of Service code.
Listen for: Second dial tone
5. Dial code for outside call.
You may be able to dial:
A trunk extension number (See Direct Trunk Access)
A trunk access code (e.g., 801)
Trunk group access code - 9 or 90-98 (See Line Rotaries)
Features: Removing Trunks to...

- For Your Notes - 
Features: Removing Trunks to Walking Class of Service
WALKING CLASS OF SERVICE
282   FEATURESN1870SWG04   Issue 1-0 

TABLE OF CONTENTS
Section 2
Programming
Table of Contents
Before Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  283
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  283
A- Toll Restriction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  289
AI- Initialize...

Table of Contents (cont’d)
E4- Next Extension in Hunt Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  347
E5- Hunt Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  349
E6- Data Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  357
E7- Page Zone . . . . . . . . . . . . . . . . . . . . ....

Table of Contents (cont’d)
H- System Status Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  413
HA- Extension-to-Port Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  413
HB- Port-to-Extension Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
HC- System Queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Table of Contents (cont’d)
QC- Operator Programming, Number of Operators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  475
QC- Operator Programming, Operator Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  476
QD- Number of System Speed Dial Digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  477
QE- Automatic Handsfree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Table of Contents (cont’d)
QT- System Timers, Traffic Management Report Wait Time . . . . . . . . . . . . . . . . . . . . . . . . . . . .  533
QT- System Timers, Loop Disconnect Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  534
QT- System Timers, Default Modem Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  535
QT- System Timers, Door Box Alert Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

- For Your Notes -
TABLE OF CONTENTS
vi   
  PROGRAMMINGIssue 1-0 

Before ProgrammingINTRODUCTION
Before Reading This Section
This section provides detailed information on each of the system’s programmable options.  Use these options to
customize your system’s features.  For example, after reading a feature description in Section 1, review the fea-
ture’s programming requirements.  Then, turn to this section for the specifics.
To change the system’s programmable options, you must connect a programming terminal to the system.  (Refer
to Connecting a Programming Terminal...