Nitsuko Digital System Feature And Terminal Programming Manual

NANP COMPATIBILITY
Description
Available in Software Levels:
BaseAUX 
> 02.40
> 02.40
Bell Communications Research (Bellcore), the administrator of the North American Numbering Plan, has issued
several important NANP rule changes that could affect your phone system.  If your software level is the same or
higher as the versions listed above, the system will accommodate the new dialing requirements with only a few
programming changes.
1.  Area (NPA) Codes and Central Office Codes can be interchangeable . ....

2.  The 950 (Feature Group B) services will be expanded . . .
Under the new rules, 7-digit 950 numbers can be more widely implemented. This may be used as an alternative
to the current 800 service, which is more difficult to dial and takes the network longer to set up. Previously, 950
numbers were always in the format 950-WXXX, where W had to be a 0 or a 1. Since the available XXX num-
bers will soon be exhausted, Bellcore has decided to allow any four digits after the 950 exchange. In addition,
950...

NIGHT ANSWER (OFF-HOURS RINGING)
Description
Night Answer lets the attendant put the system in the night mode.  Night Answer redirects calls to their night
mode destination, as determined by Universal and Assigned Night Answer.  The attendant typically activates
Night Answer after normal working hours, when most employees are unavailable to answer calls.  The system
comes up in the day mode.
Assigned Night Answer
With Assigned Night Answer (ANA), night mode calls directly ring extensions, Ring Groups and...

Night Answer, Universal Night Answer
➣E- Extensions, ED- Trunk Control, Access Control
An extension has UNA pickup only for trunks to which it has access.  (ED- Ring Control programming
has no effect on UNA answering.) [Y=allow, N=deny]
➣E- Trunks, E2- Trunk Circuit Type
The unused trunk circuit assigned in QM below must have circuit type X.
➣E- Trunks, E9- Direct Trunk Termination / EI- Night Call Routing
Terminate each trunk to the main attendant (extension 300/port 00).
➣QM- Music/Relay Control,...

Feature Operation
To activate Night Answer (attendant only):
1. Do not lift handset.
2. Press MIC/DND.
To deactivate Night Answer (attendant only):
1. Do not lift handset.
2. Press MIC/DND.
To answer an ANA call ringing your extension:
Listen for: Trunk ring
1. Lift handset.
If you have an ESL set, this answers the call.  Skip step 2.
2. Press flashing line key.
Listen for: Conversation with caller
To answer a UNA call ringing the External Paging equipment:
Listen for: Trunk ring over the External Paging...

NON-BLOCKING ARCHITECTURE
Description
The system has a non-blocking architecture.  This means that the number of transmission paths is greater than
the number of extension and trunk ports.  In other words, all extensions and trunks can be on calls simultane-
ously, without blocking or interfering with each other.
Conditions 
None
Default Configuration
The system always has non-blocking architecture.
Programming
Required Programming
None
Other Programming
None
Related Features
Analog Station Interface...

OFF-HOOK SIGNALING
Description
With Off-Hook Signaling, a user can send an off-hook indication to a busy keyset.  This tells the busy keyset
user that they have another call waiting.  Off-Hook signaling helps important callers get through -- without wait-
ing in line for the called extension to become free.
There are two types of Off-Hook Signaling:  Off-Hook Ringing and Whisper Page.  With Off-Hook Ringing,
you hear ringing through your speaker when a new call comes in.  You can answer the waiting call....

Related Features
Analog Station Interface (ASI)/ Off-Premise Extension (OPX)
ASI and OPX extensions cannot receive Whisper Page or off-hook ringing.
Attendant Positions
An attendant should have off-hook ringing.  This allows the attendant extension to ring while the phone
displays alarms.  An attendant cannot receive Whisper Page.
Automatic Fault Reporting/Remote Maintenance
When an alarm displays, the attendant’s phone does not ring normally for incoming calls.  If the exten-
sion has Off-Hook Ringing,...

Feature Operation
To signal an off-hook extension by dialing the extension number:
1. Lift handset.
2. Press ICM.
Listen for: Dial Tone
If you have an ESL set, skip this step.
3. Dial extension number.
Listen for: Ring/Busy
If you don’t hear Ring/Busy, you can’t send an off-hook signal.
If you press a DSS key instead, skip to step 4 (without dialing 1).
4. Dial 1.
Listen for: Two beeps (for Whisper Page) or
Ringing (for off-hook ringing)
5.
-If you hear two beeps, you can begin speaking.
OR
-If you hear...

To respond to off-hook ringing you hear over your speaker:
If you are on an outside call - 
Listen for: One beep (repeated)
If you are on an Intercom call - 
Listen for: One beep (repeated)
1. (Optional) Press HOLD.
If you are on an Intercom call, this saves your first call.  If you are on an outside call, hold is auto-
matic when you go to step 2.
2. Press flashing ICM.
Listen for: Conversation with second caller
To switch (alternate) between the calls, use the Split feature.
User-Programmable...