Nitsuko Digital System Feature And Terminal Programming Manual

PBX/CENTREX COMPATIBILITY
Description
The system trunks can connect to Centrex/PBX lines, rather than to telco trunk circuits.  If installed behind a
PBX, the trunk inputs into the system are 500/2500 compatible Centrex/PBX extensions.  PBX/Centrex Com-
patibility lets the system be a node in a larger private telephone network.  To make the system compatible with a
Centrex/PBX, the system administrator:
•Enters the PBX/Centrex trunk access codes into the system
•Designates trunks as PBX/Centrex lines...

Speed Dial
If a Speed Dial number uses a DP trunk and contains a pause, Pulse to Tone Conversion is automatic.
The digits before the pause dial out DP.  The digits after the pause dial out DTMF. This may affect
PBX/Centrex operation.
Station Message Detail Recording
The SMDR report also includes PBX access codes, if dialed.
Toll Restriction
If a trunk is a PBX trunk, Toll Restriction begins after the user dials the PBX access code.
If only the PBX/Centrex should apply restriction, make no QB entries but...

PERIPHERAL CONTROL UNIT (PCU) MODULE
Description
The 12SCU/PCU Peripheral Control Unit (PCU) Module (P/N 88530) provides 12 digital station ports and
gives the DS01 system the following additional features:
 
•Two External Paging Zones 1
Each PCU provides two External Paging zones with associ-
ated control circuits.  These zones are in addition to the exter-
nal zones in each CEU.  When a user calls the external zone,
the system automatically activates the associated PCU control
circuits.
•Tone Decoder...

To designate the PCU for ONS 2500 sets, enter 3.
To designate the PCU for ONS 500 sets, enter 4.
To designate the PCU for fax/modem switching, enter 5.
To designate the PCU for fax/telephone switching, enter 6.
➣QV- Peripheral Ports, PCU Sensor
For each sensor (1-4), enter 0 if sensor is connected to a Normally Open alarm contact.  Enter 1 if sensor
is connected to a Normally closed alarm contact.
➣QV- Peripheral Ports, PCU Sensor Control
For each extension and each sensor (1-4), enter Y if activating...

To answer a call from the PCU on-premise telephone:
Only the telephone connected to the Primary PCU port rings.
1. Lift handset.
The chart below shows the PCU on-premise extension numbers. 
SCU/PCU OPX Extension Numbers
Module Software Y2.1 Software Y3.1
Main CEU
(Inside)344 368
Main CEU
(Outside)345 369
Exp 1 CEU
(Inside)346 370
Exp 1 CEU
(Outside)347 371
Features: Group Call Pickup - Release Key
PERIPHERAL CONTROL UNIT (PCU) MODULE
194   FEATURESN1870SWG04   Issue 1-0 

PERSONAL GREETING
Description
Available in Software Levels:
BaseAUX 
N/A
> 02.10
An extension user can record a Personal Greeting (i.e., brief message) for their extension.  Once recorded, call-
ers to the extension hear the Personal Greeting.  Additionally, Personal Greeting can automatically forward calls
to a specified extension after the recorded greeting plays.  The user can have the recorded greeting optionally
play for all calls or just Intercom calls.
Personal Greeting lets extension users handle...

Central Office Calls, Answering / Direct Inward Line (DIL) / Transfer
Outside calls ringing an extension directly (either DILs or via Transfer) hear the Personal Greeting, if en-
abled.  The outside call then rings the specified extension.  If there is no specified extension, the call
rings all extensions with ringing for the trunk.  Outside calls ringing a line key don’t activate Personal
Greeting.
 Microphone Mute
Turning off Microphone Mute (if enabled) automatically cancels Personal Greeting....

To cancel your Personal Greeting:
1. Lift handset.
2. Press ICM.
Listen for: Dial tone
If you have an ESL set, skip this step.
3. Press PGM#.
Listen for: Dial tone stops
4. Hang up.
If you want to use Personal Greeting again, you’ll have to record a new greeting.
To erase all Personal Greetings system-wide (from your attendant or ACD Supervisor extension):
This also erases all the system’s Operator Assistance messages and the ACD All Agents Busy an-
nouncement.
1. Lift handset.
2. Press ICM.
Listen for:...

PRIME LINE SELECTION
Description
Prime Line Selection lets a keyset user answer or place an outside call by just lifting the handset.  The user does
not have to first press a line key.  This simplifies handling calls on a frequently used trunk.  There are two types
of Prime Line Selection: Ringing Prime Line and Idle Prime Line.
Ringing Prime Line
With Ringing Prime Line, the user just lifts the handset to answer a call ringing or flashing the Prime Line key.
To place a call on an idle Prime Line key,...

Related Features
Attendant Positions
Prime Line Selection does not apply to an attendant in the headset mode.
Class of Service / Night Answer (Off-Hours Ringing) / Toll Restriction
If an extension’s COS has CP- Allow Only Intercom Calls at Night (BY0:2=1), the extension cannot use
Prime Line Selection at night.
Dialing Number Preview
If an extension has Prime Line Selection, the system selects the Prime Line when the user presses DIAL.
Headset Compatibility
Prime Line Selection does not apply to an...