Nitsuko 124i/384i Software Manual

Programming (Cont’d)
In Program 0402 Item 2,
enter 0 (for Transfer) or 1
(for Serial Call).NoYes
In Program 0402 Item
2, enter 2.Should keyset TRFR
key activate Flash?
In Program 0901 Item 5,
always set the Flash type
for open loop (0).
NoYes Disconnect
CallTrunks
Features
Assign a Class of
Service to 500/2500
sets.
Stop
In 0406 Item 1, disable
flash for 500/2500 sets
(0).In 0406 Item 1, enable
Flash for 500/2500 sets
(1).Should 500/2500
sets be able to
Flash trunks?
In Program 0901 Item
6, set trunk...

Related Features
PBX Compatibility
If the system is behind a PBX, Flash normally gives the extension user access to many PBX features.
Toll Restriction
The system applies Toll Restriction (if applicable) to the number a user dials after flashing a trunk.
Operation
To flash the trunk you are on:
Keyset
1. Press FLASH.
OR
Single Line Set
1. Hookflash.
2. Dial #3.
Features D-M
Flash
292   FEATURES92000SWG08  Issue 1-0 

Flexible System Numbering
Description
 124i Available. 384i Available.
- Complete numbering flexibility
requires Base 2.13, EXCPRU 2.18 or
higher.- Complete numbering flexibility
requires system software 3.04 or
higher.
Flexible System Numbering lets you reassign the system’s port-to-extension assignments.  This allows an em-
ployee to retain their extension number if they move to a different office.  In addition, factory technicians can
make comprehensive changes to your system’s number plan.  You can...

Programming
No NoNo
Yes Yes
YesNo
Yes
Stop
Go to 0510 - Trunk
Access Code.
Go to 0512 - Single Digit
Service Code Setup.
Go to 0511 - Service Code
Setup (Part A) and 0514 -
Service Code Setup (Part B).
Go to 0501 - System
Numbering.
Do you want to change the
Trunk Access Code
(normally 9)?
Do you want to modify the
Single Digit (post-dialing)
Service Codes?
Do yo want to customize
the systems Service
Codes?
Do you want to change the
systems internal (Intercom)
numbering plan?No
Yes
NoYes
The extension...

Programming (Cont’d)
➣
0501 - System Numbering
Customize the system’s internal (Intercom) numbering plan. 
➣0502 - Extension Numbers and Names
Assign extension numbers to extension ports. The telephone’s programming identity follows the port
number - not the extension number.
➣0510 - Trunk Access Code
Assign the single-digit trunk access code (normally 9) for ARS/Trunk Group Routing.
➣ 0511 - Service Code Setup (Part A)
Customize the first set of Service Codes. Also see Program 0514.
➣0512 - Single Digit...

Forced Trunk Disconnect
Description
 124i Available 384i Available
Forced Trunk Disconnect allows an extension user to disconnect (release) another extension’s active outside call.
The user can then place a call on the released trunk. Forced Trunk Disconnect lets a user access a busy trunk in
an emergency, when no other trunks are available. Maintenance technicians can also use Forced Trunk Discon-
nect to release a trunk on which there is no conversation. This can happen if a trunk does not properly...

Related Features
Central Office Calls, Placing
A user can use Forced Trunk Disconnect only for trunks to which it would normally have access.
Operation
To disconnect a busy trunk:
Keyset
1. Press line key for trunk.
OR
Dial trunk access code (#9 + trunk number).
You hear busy tone. Trunk numbers are 001-128.
2. Dial *3.
You hear confirmation beeps as the system disconnects the trunk.
You can now place a call on the free trunk.
Single Line Telephone
1. Dial trunk access code (#9 + trunk number)
You hear...

Group Call Pickup
Description
 124i Available — eight Call Pickup
Groups. 384i Available — 32 Call Pickup Groups.
Group Call Pickup allows an extension user to answer a call ringing an extension in a Pickup Group.  This per-
mits co-workers in the same work area to easily answer each other’s calls.  The user can intercept the ringing
call by dialing a code or pressing a programmed Group Call Pickup key. If several extensions within the group
are ringing at the same time, Group Call Pickup intercepts...

Programming
Start
Should extension be
in a Pickup Group?
In 1012, assign extensions to
Pickup Groups (1-8 in 124i, 1-32
in 384i) and set each extensions
priority within the group (1-96 in
124i, 1-384 in 384i).In 1012, assign
extensions to
Pickup Group 0.
Should extension be able
to use Group Call Pickup?In 0406 Item 63,
enter 1.In 0406 Item 63,
enter 0.
Should extension be able to
pick up a call ringing their
own Pickup Group (Service
Code 856 or 867)?Service Code 856 cannot pick
up Ring Group Calls.In...

Programming (Cont’d)
No Yes No Yes
Stop
In 1005, assign
Class of Service to
extensions.
In 0406 Item 51,
enter 0.Trunk 
Pickup GroupIn 0406 Item 51,
enter 1.
After picking up a call,
should extensions display
show number of trunk
intercepted or Pickup
Group?
Continued
from the
previous
page.
In 1006, do not assign a
function key (code 1009 +
Pickup Group number).In 1006, assign a function
key (code 1009 + Pickup
Group number).Should extension have
one-button pickup for calls
ringing another (known)...