Nitsuko 124i/384i Software Manual

Programming (Cont’d
Auto-Answer of Non-Ringing Lines
No
Yes Yes NoYes
Choose from the routes you
programmed in Trunk Group Routing
(Program 0906).  Make one entry for
each Night Service mode.
Stop
In Program 1015, select
the routing sequence for
auto-answer of non-ringing
lines.In Program 0906, program
the Trunk Group Routing
table.  Refer to the Trunk
Group Routing feature.
In Program 0905, assign
trunks to groups.  Refer to the
Trunk Group feature.Is Trunk Group
Routing
programmed?
In Programs 0909 and...

Programming (Cont’d)
➣
0401 - Tenant Group Options, Part A, Item 8: Incoming Call Priority
For each tenant group, determine if ringing Intercom calls (0) or ringing trunk calls (1) should have an-
swer priority.  See the table below for interaction.
➣0401 - Tenant Group Options, Part A, Item 12: Ringing Line Preference for Intercom Calls
For each tenant group, enable Idle (0) or Ringing (1) Line Preference for Intercom calls.  See the table be-
low for interaction.
➣0401 - Tenant Group Options, Part A,...

Programming (Cont’d)
➣
0906 - Trunk Group Routing
For Auto Answer of Non-Ringing Lines, program the Trunk Group Routing table.  Auto Answer uses this
table to determine the answer sequence for ringing calls.
➣0909 - Extension Ring Group Assignment
Assign extensions to ring groups (1-128).  Auto-Answer for Non-Ringing Lines only works for trunks
that do not ring an extension.
➣0910 - Trunk Ring Group Assignment
Assign trunks to ring groups (1-128).    Auto-Answer for Non-Ringing Lines only works for...

Related Features
Direct Inward Line
DILs do not affect Incoming Line Preference operation.
Ring Groups
Trunks ring extensions according to Ring Group programming.
Trunk Group Routing
If an extension gets trunk dial tone when the user lifts the handset, the system uses the dial 9 routing to
select the trunk.
Operation
To answer a ringing call if your phone has Ringing Line Preference:
1. Refer to the chart on the previous page.
To place a call if your phone has Outgoing Line Preference:
1. Refer to the...

Loop Keys
Description
 124i Available. 384i Available.
Loop keys are uniquely programmed function keys that simplify placing and answering trunk calls. There are
three types of loop keys: Incoming Only, Outgoing Only and Both Ways. 
•Incoming Only Loop Keys
Incoming Only loop keys are for answering trunk calls. An extension can have an incoming loop key for a
specific trunk group (fixed) or a catch all loop key for any trunk group (switched). Fixed loop keys allow
an extension user to tell the type of...

Programming
Make sure the Trunk Access Map
assignments match the loop keys
requirements.Incoming loop keys flash and ring for
Ring Group calls. Loop keys use trunk
group assignments
when answering and
placing calls.Both Ways
Stop
Program Trunk Access Maps: In 0911,
set up the access options for Access
Maps. In 0912, assign Trunk Access
Maps to extensions.
In 0905, assign trunks to trunk
groups.
Program Ring Groups: In 0910, assign
trunks to Ring Groups. In 0909, assign
extensions to Ring Groups.
In 1026,...

Programming (Cont’d)
➣
0905 - Trunk Groups
Assign trunks to trunk groups (1-128). In general, loop keys access trunks within specific trunk groups.
➣0909 - Extension Ring Group Assignment
Assign extensions to Ring Groups (1-128). An incoming loop key will ring only for those trunks pro-
grammed to ring. Also see Program 0910.
➣0910 - Trunk Ring Group Assignment
Assign trunks to Ring Groups (1-128). An incoming loop key will ring only for those trunks pro-
grammed to ring. Also see Program 0909 above....

Operation
To place a call on a loop key:
1. Press outgoing or both ways loop key.
You hear dial tone and the key lights green.
2. Dial number.
To answer a call on a loop key:
Listen for ringing a look for a flashing (red) loop key.
1. Press loop key.
The key lights green and you connect to the call.
If there are additional calls waiting to be answered, your display shows: 
WAITING – LOOP KEY 
To program a loop key:
1. Press idle CALL key.
2. Dial 851.
3. Press the key you want to program as a loop key....

Meet Me Conference
Description
 124i The system allows either 8 four-
party conferences or 4 eight-party
conferences. 384i Each DTU-A/C allows either 4
four-party conferences or 2 eight-
party conferences per PCB.
With Meet Me Conference, an extension user can set up a Conference with their current call and up to six other
inside parties.  Each party joins the Conference by dialing a Meet Me Conference code.  Meet Me Conference
lets extension users have a telephone meeting -- without leaving the...

Programming (Cont’d)
YesNo
You can simplify Meet Me Conference
operation by assigning the following function
keys in 1006:  External Zone Paging (code
1004), External All Call Paging (code 1005),
Internal Zone Paging (code 1006) and Meet
Me Conference/Paging pickup (code 1010). Setting the Meet Me
Conference Time too long can
unnecessarily tie up
Conference circuits.
In 0405 Item 9, set the Meet Me
Conference Time to meet the
application.Is the time users have to join a
Meet Me Conference
adequate? No...