NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 2 80
Revision 2.0
MAT: FAULT MESSAGE
PROGRAMMING 
Refer to the Maintenance Manual. 

ND-45670 (E) CHAPTER 2
Page 281
Revision 2.0
MAT: PEG COUNT
PROGRAMMING 
Refer to the Command Manual. (Command Code: B0, B3)  

CHAPTER 2 ND-45670 (E)
Pag e 2 82
Revision 2.0
MAT: REMOVE AND RESTORE
PROGRAMMING 
DESCRIPTION DATA
Set or cancel make-busy to stations and 
trunks. • Y = 0
(1)  X-XXXX: Station Number. 
(2) 0: Make-busy Set
1 : Make-busy cancel 
• Y = 1
(1) 000-255: Trunk Number
(2) 0 : Make-busy Set
1 : Make-busy cancel 
START
END
CME5 

ND-45670 (E) CHAPTER 2
Page 283
Revision 2.0
MAT: STATION/TRUNK STATUS
PROGRAMMING 
Refer to the Maintenance Manual. 

CHAPTER 2 ND-45670 (E)
Pag e 2 84
Revision 2.0
MESSAGE CENTER INTERFACE (MCI)
PROGRAMMING
Refer to the Message Center Interface (MCI) System Manual. 

ND-45670 (E) CHAPTER 2
Page 285
Revision 2.0
MESSAGE REMINDER
PROGRAMMING
To provide Message Reminder service for each station:
 
DESCRIPTION DATA
MSG Display. (1) 025
(2) 0/1 : MSG (only) /MSGX (X: No. of 
messages)
To activate the Single-Digit Feature Access 
Code (1, 2, 3 and 6) feature, set the data for 
050, 051, 069 and 148 to “1.”(1)  050: *Button as Switch Hook-Flash.
(2) 1 : Ineffective
(1)  051: #Button as Switch Hook Flash.
(2) 1 : Ineffective
(1)  069 : Single-Digit Dialing/on BT Con-...

CHAPTER 2 ND-45670 (E)
Pag e 2 86
Revision 2.0
MESSAGE REMINDER
HARDWARE REQUIRED 
For providing the Single-Line Telephone with Message-Waiting Lamp:
- PN-4LCD card ´ n/4 (n: Number of Telephone sets equipped with MW Lamp) 
For providing Multiline Terminal
- ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card. 
DESCRIPTION DATA
Provide the Message Reminder service for 
each station.•  YY = 03
(1)  X-XXXX: Station No. 
(2)  0: To be provided (for stations with 
MW lamp or Multiline...

ND-45670 (E) CHAPTER 2
Page 287
Revision 2.0
MESSAGE WAITING
PROGRAMMING
Refer to the DSS/BLF Console feature to program the DSS/BLF as a Message Front Station.
DESCRIPTION
Assign the class of service for Message 
Waiting to required stations as shown below.• CM12 YY=02 [Service Restriction Class 
A (00-15t)] 
• CM15 YY=24 (Administrative
Station allowing Mes-
sage Waiting Set/Reset to 
station) 
• CM15 YY=40 (Station setting MW) 
(1) Service Restriction Class (A) (00-15) 
(2) 0/1 : Restricted/Allowed...

CHAPTER 2 ND-45670 (E)
Pag e 2 88
Revision 2.0
HARDWARE REQUIRED
To provide a Single-Line Telephone with the Message Waiting Lamp:
• PN-4-LCD Card
DESCRIPTION
If an ATTCON is assigned as the Message 
Front destination by CM51 YY=15, set the 
data for 233 to 0. With this setting, Message 
Waiting is automatically reset when the 
ATTCON answers.(1) 233 
(2) 0
To reset the Message Waiting indication while 
the Message Front Station rings by dialing the 
MW Retrieve/Search access code or pressing 
the MW key...

ND-45670 (E) CHAPTER 2
Page 289
Revision 2.0
MISCELLANEOUS TRUNK ACCESS: CODE CALLING EQUIPMENT ACCESS
PROGRAMMING
DESCRIPTION DATA
Assign the interface trunk (PN-4COT and/
PN-DK00) to the required LEN. 
Note:The PN-DK00 Card No. must be as-
signed to the first LEN (Level 0)
and/or the third LEN (Level 2). (1) LEN (0000-0511) 
(2) D000-D255: PN-4COT
E800-E831: PN-DK00
E800-E807: For PIM0/1 
E808-E815: For PIM2/3 
E816-E823: For PIM4/5 
E824-E831: For PIM6/7 
Assign the trunk data to the Trunk Number. •...