NEC Neax2000 Ivs Command Manual

CHAPTER 3 ND-45669 (E)
Pag e 2 94
Revision 2.0
CM90
COMMAND CODE
TITLE:
MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT
90
MAT
• ATTCON Function Keys
YY
SETTING
DATAFUNCTIONSTANDARD 
KEY
SETTINGREMARKSRELATED
COMMAND
No. MEANING
00
(Key 
data)Setting of 
FunctionF6100 Room Cut Off (RC) For Hotel ATTCON
Note 1
F6101 Message Waiting (MW)
F6102 Do Not Disturb (DND)
F6103 Wake Up/Do Not Disturb 
Override (WU/OV)
F6104 Reset (RESET)
F6105 Serial Call Set (SC) CM90-F6062
F6106 Flash over trunk...

ND-45669 (E) CHAPTER 3
Pag e 2 95
Revision 2.0
CM90
COMMAND CODE
TITLE:
MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT
90
MAT
00
(Key 
data)Setting of 
FunctionF6121 Last umber Redial/Stack Dial
F6122 Calling Number/Calling 
Name Display for Caller ID 
Class
F6123 Transfer to VMS
F6144 Call Park-System CM08-445
F6150
F6159Paging 0
Paging 9CM08-445
F6200 Source (SRC) SRC
F6201 Destination (DEST) DEST
F6202 Cancel (CNL) CANCEL
F6203 Talk (TALK) TALK
F6204 Hold (HOLD) HOLD
F6205 Start (START)...

CHAPTER 3 ND-45669 (E)
Pag e 2 96
Revision 2.0
CM90
COMMAND CODE
TITLE:
MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT
90
MAT
• ATTCON Multi-Function Keys
YY
No.AT T C O N  
STATUS 
No.MEANINGSETTING
DATAFUNCTION REMARKSRELATED
COMMAND
00 00
(Idle State)Idle State F6100 Room Cut Off 
(RCOF)
F6102 Do Not Disturb 
(DND)
F6104 Reset (RESET)
F6110 Mode (MODE)
F6111 Programming 
(PROG)DISA, System 
Speed Dialing, 
Date and Time 
and Tone Ringer
01
(ANS & 
ORG)When answering 
or originatingF6105...

ND-45669 (E) CHAPTER 3
Pag e 2 97
Revision 2.0
CM90
COMMAND CODE
TITLE:
MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT
90
MAT
Note 1:Use the ANSWER key as the SET key for Hotel/Motel features.
Note 2:Call Processing keys or Loop keys should not be assigned to the Multi-Function Key (01 – 06).
Note 3:When setting or cancelling a group of stations in DND/RC, use ATTCON status No. 00.
Note 4:See related command, CM60 YY = 17.
00 04
(Hotel/
Motel)When accessing 
Hotel/Motel
featuresF6100 Room...

CHAPTER 3 ND-45669 (E)
Pag e 2 98
Revision 2.0
CM90
COMMAND CODE
TITLE:
MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT
90
MAT
Note 5:If no data is set, the Multi-Function keys are automatically set by initial data/Resident System
Program as follows:
• Idle State
• When answering or originating
• When the called station is busy
• When the called station is in DND
• When accessing Hotel/Motel feature
010203040506
MODE: Mode
PROG: ProgrammingPA 10:23 AM TUE 12
MODE PROGLOCKOUT/DAY...

ND-45669 (E) CHAPTER 3
Pag e 2 99
Revision 2.0
CM90
COMMAND CODE
TITLE:
MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT
90
MAT
4.3 Add-On Module
: Initial Data
YY SETTING DATA
RELATED
COMMAND
No. MEANINGKEY 
No.DATA MEANING
00
(Key 
Data)Setting of Functions 30
54X
XXXX
(STA No.)Station Number
• Primary Extension Number (FX-FXXXX)
• Multiline Number (Ordinary Station)
• Multiline Number (assigned by CM11)
X=0-9, A (*), B (#)CM10
CM11
A000
A031
A100
A131Automatic Intercom Number CM11 
CM56...

CHAPTER 3 ND-45669 (E)
Pag e 3 00
Revision 2.0
CM90
COMMAND CODE
TITLE:
MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT
90
MAT
00
(Key 
Data)Setting of Functions 30
 89F11XX XX
00: Station Speed Dialing 00
99: Station Speed Dialing 99CM73
(SPD0099) CM74
00 Setting of Functions 87
89F0043
(D/N)Day/Night Key
Note:Any one of key numbers 87
through 89 can be used for the
Day/Night key.
01
(RG)Tone Ringer enabled 
on call termination30
540
1Disabled
Enable
03 Ringer sending method 
when...

ND-45669 (E) CHAPTER 3
Pag e 3 01
Revision 2.0
CM93
COMMAND CODE
TITLE:
PRIME LINE
93
MAT
4. DATA TABLE:
Note:Any station number or Virtual Line number can be assigned to the Prime Line.
A single-line telephone cannot be assigned as the Prime Line.
1. FUNCTION:
This command is used to assign the prime line to a station line or a trunk line on a Multiline Terminal.
The prime line is the line seized when the Multiline Terminal user goes off-hook or presses the speaker
button.
2. PRECAUTION:
(1) Any one...

CHAPTER 3 ND-45669 (E)
Pag e 3 02
Revision 2.0
CM94
COMMAND CODE
TITLE:
MULTILINE TERMINAL ONE-TOUCH MEMORY
94
MAT
4. DATA TABLE:
Note 1:If “4” is selected, the first 10-Slot Memory Block number must be “00” through “49”.
Note 2:1000-Slots Memory Block Number 8-F can be used when the system provides the Extension Mem-
ory card. If assigning the station number to One Touch keys using this memory area, the lamp
does not show the busy state.
1. FUNCTION:
This command is used to assign memory for the storage...

ND-45669 (E) CHAPTER 3
Pag e 3 03
Revision 2.0
CM96
COMMAND CODE
TITLE:
DSS CONSOLE NUMBER
96
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign a DSS Console to a station, Multiline Terminal or attendant console.
2. PRECAUTION:
This command is included in MAT mode menu “E3” (DSS Console No. & Keys [COM02]).
3. ASSIGNMENT PROCEDURE:
DSS CONSOLE
NUMBERSETTING DATA
RELATED
COMMAND
DATA MEANING
00
31
(See CM10, E100-E131)X
XXXXSingle Line Telephone Station Number or Primary 
Extension Number of...