NEC Neax 2400 Ipx Fusion Network System Manual

CHAPTER 5 NDA-24299
Page 66
Revision 1.0
DATA PROGRAMMING
Assignment of System Data
STEP 4: ASYDL and ASYDN
Assign other system data using the ASYDL/ASYDN command.
When Timing Start is used, assign the following data.
Index 161 b6 : 0/1=-/Timing Start using “#” code
b7 : 0/1=-/Timing Start using “*” code
Index 170 b4 : 0/1=Timing Start out of Service/Timing Start in Service 
Note 1
Index 640 Fusion Point Code (FPC) of node providing ATTCON Note 2
Index 704~735 (ASYDL)
FPC of the node to which ATTCON...

NDA-24299 CHAPTER 5
Page 67
Revision 1.0
DATA PROGRAMMING
Assignment of System Data
When “different numbering development on a TN basis” is not required, set the above bits. Figure 5-8 shows
the display of the ASYDN command Index 514 as an example. 
Figure 5-8   ASYDN Command Display (Example)
Note 4:
Be sure to execute “Non-Load Initial” after setting the FPC data. The assigned FPC becomes effective by
this operation.
1 

CHAPTER 5 NDA-24299
Page 68
Revision 1.0
DATA PROGRAMMING
Assignment of FPC and MG and UNIT into Network
3. Assignment of FPC and MG and UNIT into Network
3.1 AFMU
Assign the module accommodation data by giving Module Group Number and Unit Number on an FPC
basis. This data is necessary to allocate unique Network ID (NID) to each MG/UNIT of the whole Fusion
network nodes. 
Note:This data can be set at the NCN only. A unique NID is assigned to each MG/UNIT automatically by entering
the AFMU data.
When the...

NDA-24299 CHAPTER 5
Page 69
Revision 1.0
DATA PROGRAMMING
Assignment of Logical RT in Network DM (NDM)
4. Assignment of Logical RT in Network DM (NDM)
4.1 ALRTN/ARTKN
Use this command to assign Logical Route Numbers to all external trunks used on a Fusion network.
Assign unique telephone numbers to the whole route for external trunks on the network (including COT,
DAT, Dummy Route, etc.) using this command. The data can be set at the NCN only and should be set for
every external route in every node....

CHAPTER 5 NDA-24299
Page 70
Revision 1.0
DATA PROGRAMMING
Assignment of Numbering Data for Telephone Numbers
The ALRTN command display should look similar to Figure 5-13:
Figure 5-13   ALRTN Command Display
5. Assignment of Numbering Data for Telephone Numbers
STEP 1: ANPDN
Make a telephone numbering plan on the network. The explanation is given here on the assumption
that the network adopts the numbering plan shown in Figure 5-14. Therefore, modify the data
assignment explained here when you assign the...

NDA-24299 CHAPTER 5
Page 71
Revision 1.0
DATA PROGRAMMING
Assignment of Numbering Data for Telephone Numbers
STEP 2: ANPDN
Assign Pre-translation Data for the telephone numbers planned in Step 1 using the ANPDN command
at NCN. Figure 5-15 shows the data setting for ANPDN.
Figure 5-15   ANPDN Sample Data Sheet
The ANPDN command display should look similar to Figure 5-16:
Figure 5-16   ANPDN Command Display
Note:
Perform the Numbering Plan data setting by using ANPD command as assigned by ANPDN command.
-...

CHAPTER 5 NDA-24299
Page 72
Revision 1.0
DATA PROGRAMMING
Assignment of Numbering Data for Telephone Numbers
STEP 3: ASPAN
Assign special access code data for the telephone numbers using the ASPAN command. SRV=TELN
is the data for telephone numbers. Figure 5-17 and Figure 5-18 show a sample data sheet and
command display for ASPAN.
Figure 5-17   ASPAN Sample Data Sheet
Figure 5-18   ASPAN Command Display
Note:
The Numbering Plan data for the LDM and/or NDM cannot use separate Tenant Numbers (TN), so be...

NDA-24299 CHAPTER 5
Page 73
Revision 1.0
DATA PROGRAMMING
Assignment of Telephone Numbers
6. Assignment of Telephone Numbers
This section explains how to program telephone numbers. To program telephone numbers, use ALGSN
command. A telephone number can be assigned to a station with the use of the LENs or the Physical Station
Number depending on programming.
Note:The Fusion link must be operational before telephone numbers can be programmed in the Fusion network.
COMMAND: ALGSN/ATSTN
Assign telephone...

CHAPTER 5 NDA-24299
Page 74
Revision 1.0
DATA PROGRAMMING
Assignment of Telephone Numbers
Figure 5-20   ALGSN Command Display (Example)
UGN
TELN
WRT? 
ALGSN (Assignment of Telephone Station Data In Network)
11
Y
FPC
141000 TYPE
LENS
000100
Physical LENS Telephone Num ber
 
For Help, press F1
 
NUM
UGN
TELN
WRT? 
ALGSN (Assignment of Telephone Station Data In Network)
21
Y
FPC
1TN
1 41000 TYPE
STN
2000
Physical Station N um ber Telephone Num ber
 
For Help, press F1
 
NUM 

NDA-24299 CHAPTER 5
Page 75
Revision 1.0
DATA PROGRAMMING
Assignment of Telephone Numbers
6.1 Assignment of Connection Route/Trunk Data
STEP 1: ACRD
Using the ACRD command, assign the connection route data of Fusion link. The data must be
assigned for both B-channel and D-channel. Assign appropriate data referring to Table 5-1.
Figure 5-21 shows an example of route numbers for B-ch and D-ch.
Figure 5-21   B-ch and D-ch (Example)
The ACRD command display should look similar to Figure 5-22.
Figure 5-22...