NEC Neax 2400 Ipx Fusion Network System Manual
Here you can view all the pages of manual NEC Neax 2400 Ipx Fusion Network System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 61
CHAPTER 4 NDA-24299 Page 46 Revision 1.0 INSTALLATION Connecting Cables 4.2 Connecting 10 BASE-T Cables Figure 4-11 shows sample cable connections, where HUB (PA-M96) cards are provided in a dual configuration and the FCH (PA-FCHA) card is located in PIM 1 (1-IMG system/IMG0). When HUB cards are provided in a dual configuration, the two HUB cards must be connected on each front edge connector with a 10 BASE-T cross cable. However, when dual LANIs (LANI-A and LANI-B) are used for each CPU, the cross cable...
Page 62
NDA-24299 CHAPTER 4 Page 47 Revision 1.0 INSTALLATION Connecting Cables 4.3 10 BASE-T Connection Procedure The pattern for 10 BASE-T cable connections may vary, depending on the system configuration (such as the number of IMG stacks or the mounting location/number of the FCH/HUB cards, etc.). According to your system configuration, connect necessary Ethernet cables: 4.3.1 Procedure for 1-IMG System If your system is 1-IMG type, the 10 BASE-T connection should use either of the following cables: 1. Cable...
Page 63
CHAPTER 4 NDA-24299 Page 48 Revision 1.0 INSTALLATION Connecting Cables 4.3.3 When not using the cable unit SR1201 ETIF CAU-n When your system doesn’t use the cable unit classified as SR1201 ETIF CAU-n, perform the 10 BASE- T connections as instructed below: 1. Depending on your system configuration, connect the 10 BASE-T straight cable(s) between the HUB (PA-M96) and LANI (PZ-PC19) cards. Use the cable UTP CTG5 ST CA-O, which must be provided by the user. When a single LANI is used for each CPR (Slot 00...
Page 64
NDA-24299 CHAPTER 4 Page 49 Revision 1.0 INSTALLATION Connecting Cables When dual LANIs are used in both Slot 00 and 03 of CPR#0/CPR#1, be sure to use at least two HUB cards as separate 10 BASE-T connection terminals. Use one HUB for the internal LANI (LANI-A: in Slot 00 of each CPR), and use the other for the external LANI (LANI-B in Slot 03 of each CPR). 2. When the HUB is in a dual configuration, connect the 10 BASE-T cross cable between the HUB cards. Use the following cables, which are provided by...
Page 65
CHAPTER 4 NDA-24299 Page 50 Revision 1.0 INSTALLATION Connecting Cables When dual FCH is provided for the HUB dedicated to each internal LANI card (LANI-A: in Slot 00 of each CPR), connect FCH#0 to HUB#0 and FCH#1 to HUB#1. When your system also uses the external LANI cards (LANI-B in Slot 03 of each CPR), prepare another set of FCH cards for the HUB dedicated to the external LANI cards. Then, if the FCH is in dual configuration, connect one FCH to the HUB for No. 0 system of the external LANI, and the...
Page 66
NDA-24299 CHAPTER 4 Page 51 Revision 1.0 INSTALLATION Connecting Cables Figure 4-13 shows some typical examples where 10 BASE-T cables are connected to the FCH card(s) mounted in PIM0 of 1-IMG system, under the conditions in Table 4-6: Table 4-6 Connection of 10 BASE-T Cables to FCH Card(s) in PIM0 of 1-IMG Note 1: Cables Contained in each cable unit are as follows: SR1201 ETIF CAU-A: UTP CTG5 ST CA-D, UTP CTG5 ST CA-J SR1201 ETIF CAU-DA: UTP CTG5 ST CA-D, UTP CTG5 ST CA-J, UTP CTG5 CRS CA-F Note 2:The...
Page 67
CHAPTER 4 NDA-24299 Page 52 Revision 1.0 INSTALLATION Connecting Cables Figure 4-13 Examples of Ethernet Cable Connection-FCH in PIM0 (1-IMG System) (2/2) ATTENTIONContents Static S ensitive Handling Precautions Required 06 04 05 03 02 01 0006 04 05 03 02 01 00 CN CN CNCN HUB CN CNHUB BASEU PIM 1 PIM 2 PIM 3 UTP CTG5 ST CA-J PIM 0 LPMTOPU FANU BSCM CN FC H CN UTP CTG5 ST CA-J FCH CNCN UTP CTG5 ST CA-D < F C H in P IM 0 (P attern 3)> < F C H in P IM 0 (P a ttern 4)> 06 04 05 03 02 01 00 06 04 05...
Page 68
NDA-24299 CHAPTER 4 Page 53 Revision 1.0 INSTALLATION Connecting Cables Figure 4-14 shows some typical examples where 10 BASE-T cables are connected to the FCH card(s) mounted in PIM1 of 1-IMG system, under the conditions in Table 4-7: Table 4-7 Connection of 10 BASE-T Cables to FCH Card(s) in PIM1 of 1-IMG Note 1: Cables contained in each cable unit are as follows: SR1201 ETIF CAU-B: UTP CTG5 ST CA-K, UTP CTG5 ST CA-J SR1201 ETIF CAU-DB: UTP CTG5 ST CA-I, UTP CTG5 ST CA-J, UTP CTG5 CRS CA-F Note 2:The...
Page 69
CHAPTER 4 NDA-24299 Page 54 Revision 1.0 INSTALLATION Connecting Cables Figure 4-15 shows some typical examples where 10 BASE-T cables are connected to the FCH card(s) mounted in PIM2 of 1-IMG system, under the conditions in Table 4-8: Table 4-8 Connection of 10 BASE-T Cables to FCH Card(s) in PIM2 of 1-IMG Note 1: Cables contained in each cable unit are as follows: SR1201 ETIF CAU-C: UTP CTG5 ST CA-M, UTP CTG5 ST CA-J SR1201 ETIF CAU-DC: UTP CTG5 ST CA-K, UTP CTG5 ST CA-J, UTP CTG5 CRS CA-F Note 2:The...
Page 70
NDA-24299 CHAPTER 4 Page 55 Revision 1.0 INSTALLATION Connecting Cables Figure 4-15 Examples of Ethernet Cable Connection-FCH in PIM2 (1-IMG System) (2/2) ATTENTIO NContents S ta tic S en s itive Handling Precautions Required 06 04 05 03 02 01 00 06 04 05 03 02 01 00 CN CN CN CNCN CNUTP CTG5 ST CA-J CNFC H HUB CN HUB BASEU PIM 1 PIM 2 PIM 3 LPM CN CN FANU PIM 0 CN FCH CN UTP CTG5 ST CA-M UTP CTG5 ST CA-K UTP CTG5 ST CA-J TO PU 06 04 05 03 02 01 0006 04 05 03 02 01 00 CN CNCN CN HUB CN CNHUB BASEU PIM...