NEC Neax 2400 Ipx Fusion Network System Manual
Here you can view all the pages of manual NEC Neax 2400 Ipx Fusion Network System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 71
CHAPTER 4 NDA-24299 Page 56 Revision 1.0 INSTALLATION Connecting Cables Figure 4-16 shows some typical examples where 10 BASE-T cables are connected to the FCH card(s) mounted in PIM3 of 1-IMG system, under the following conditions: Table 4-9 Connection of 10 BASE-T Cables to FCH Card(s) in PIM3 of 1-IMG Note 1: Cables contained in each cable unit are as follows: SR1201 ETIF CAU-D: UTP CTG5 ST CA-N, UTP CTG5 ST CA-J SR1201 ETIF CAU-DD: UTP CTG5 ST CA-L, UTP CTG5 ST CA-J, UTP CTG5 CRS CA-F Note 2:The...
Page 72
NDA-24299 CHAPTER 4 Page 57 Revision 1.0 INSTALLATION Connecting Cables Figure 4-16 Examples of Ethernet Cable Connection-FCH in PIM3 (1-IMG System) (2/2) ATTENTIONContents Static Sensitive Handling Precautions Required 06 04 05 03 02 01 0006 04 05 03 02 01 00 CN CNCN CN HUB CN CNHUB BASEU PIM 1 PIM 2 PIM 3 UTP CTG5 ST CA-J PIM 0 LPMFANU BSCM BSCM CN FCH CN UTP CTG5 ST CA-J FCH CN CN UTP CTG5 ST CA-N TOPU 06 04 05 03 02 01 00 06 04 05 03 02 01 00 CN CN CN CNCN CNUTP CTG5 ST CA-J CN FC H HUB CN HUB...
Page 73
CHAPTER 4 NDA-24299 Page 58 Revision 1.0 This page is for your notes.
Page 74
NDA-24299 CHAPTER 5 Page 59 Revision 1.0 CHAPTER 5 DATA PROGRAMMING This chapter explains how to set Fusion network data, using the following data categories: System Data Numbering Plan Data Station Data Fusion Link Data Figure 5-1 shows the overall data programming procedure: Figure 5-1 Data Programming Flow Chart AFMU ANPD ANPDL STN SSC SSCA OGC OGCA LCR LCRS UNIF : : : ------------ SSC ------ OGC OGCA LCR LCRS : : : TELN Note ASDT System Data Numbering Plan Data Station Number Data...
Page 75
CHAPTER 5 NDA-24299 Page 60 Revision 1.0 DATA PROGRAMMING Network Data Programming Summary 1. Network Data Programming Summary This section provides a summary of the data programming of Fusion systems. 1.1 Brand-new Fusion Network To install the Fusion network as a brand-new system, follow the overall data programming procedure below. 1.1.1 System Data Decide an NCN and LN on the network. Assign System Data for each node. Use the ASYDN command for the NCN and the ASYDL command for all nodes. The system...
Page 76
NDA-24299 CHAPTER 5 Page 61 Revision 1.0 DATA PROGRAMMING Network Data Programming Summary 1.1.4 Fusion Link Data Assign the Fusion link data using the following commands: Fusion with FCH:ACRD → ACTK → ACAN → MBCT → AFCH → AFPC → AFRT Fusion w/o FCH:ACRD → ACTK → ACAN → MBCT → AFPC 1.2 Upgrading a CCIS Network To install the Fusion system to an existing CCIS network, follow the overall programming procedure below: 1.2.1 System Data Decide an NCN and LN on the network. Assign...
Page 77
CHAPTER 5 NDA-24299 Page 62 Revision 1.0 DATA PROGRAMMING Network Data Programming Summary Note: When the Fusion system is incorporated in an existing CCIS network, all nodes must be linked via CCIS on the network. If there are any nodes linked via ACIS alone, add the CCIS link before installing the Fusion link. (See Figure 5-2.) Refer to CCIS-related manuals for more detailed information. 1.3 Fusion Link Data Assign the Fusion link data using the following commands: Fusion with FCH: ACRD ➔ ACTK ➔ MBCT...
Page 78
NDA-24299 CHAPTER 5 Page 63 Revision 1.0 DATA PROGRAMMING Network Data Programming Summary Figure 5-3 shows how to upgrade an existing CCIS network, focusing on the Numbering Plan. The example data setting assumes the existing network uses this particular numbering. For more detailed information on how to assign telephone numbers, see Assignment of Telephone Numbers. Figure 5-3 How to Upgrade the Numbering Plan Data of an Existing CCIS Network Before Upgrading STN: 2000 A CB 80 82 81 STN: 2000 STN:...
Page 79
CHAPTER 5 NDA-24299 Page 64 Revision 1.0 DATA PROGRAMMING Assignment of System Data 2. Assignment of System Data STEP 1: ASYDL and ASYDN Assign the number of data memory blocks for the Network Data Memory (NDM) and the Local Data Memory (LDM). Use the ASYDN command for the NCN. Use the ASYDL command for all nodes. Figure 5-4 shows ASYDL Indexes 513 and 514 as an example. Figure 5-4 Assignment of Memory Block (1) Assign the following data to all nodes. ASYDL, Index 513 Local Data Memory (LDM) usage...
Page 80
NDA-24299 CHAPTER 5 Page 65 Revision 1.0 DATA PROGRAMMING Assignment of System Data STEP 2: ASYDL Assign the self-Fusion Point Code (self-FPC) at each node. FPC ranges from 1 to 253. Use the ASYDL command. (Index 512 b0-b7) Index 512 self-Fusion Point Code Assign a unique FPC for each node. Figure 5-6 shows an example of FPC assignment. Figure 5-6 Self-FPC Assignment STEP 3: ASYDL Assign the data of DP (Dial Pulse) relay broadcasting to Fusion Link using the ASYDL command (Index 527, b4): 0/1=DP relay...