NEC Neax 2400 Ipx Fusion Network System Manual

CHAPTER 5 NDA-24299
Page 96
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 5: ARTD/ARTDN
Using ARTD, assign the following CDN data for the dummy route number. 
Note 1
CDN 6 (TCL)=1 or 4 (depending on requirement) 
CDN 7 (L/T)=1
CDN 13 (AC)=1
The other CDNs may be left default (data 0) for the dummy route.
STEP 6: AFRSL/AFRSN  
Note 2
Using AFRSL, assign the Number Pattern Code (NPC) and the Outgoing Route Selection Pattern
Number (OPR) for the dummy route number.
LGRT=Dummy route...

NDA-24299 CHAPTER 5
Page 97
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
7.2 Data Assignment for 52M-SDH Interface
This section explains the Fusion Connection with 52M-SDH interface. Figure 5-42 explains the connection
pattern.
Figure 5-42   Fusion Connection with 52M-SDH Interface
F u s i o n
Node-A
Optical Fiber Cable
Optical Fiber Cable
For Dual Configuration Connection Link (Data Link)
Connection Trunk (Speech Path)
Internal LAN
FCH
S 
D 
T 
B
Node-B
Internal LAN
S 
D 
T 
BFCH+
Fusion...

CHAPTER 5 NDA-24299
Page 98
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
Specifications for the SDH data setting are described below.
1. When FCCS and CCIS links are used together in the network, a different route number must be assigned
to each Connection Trunk (B-ch), Connection link (D-ch), Speech Line for CCIS, and Signal Line for
CCIS. Figure 5-43 provides an example.
Figure 5-43   Assignment of Different Route Numbers for FCCS and CCIS Links (example)
2. System data (SYS1, INDEX...

NDA-24299 CHAPTER 5
Page 99
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
Connection link (for Data)
C_RT: 11
TCL=4 LSG=13
STEP 3: ACTK
Assign the Connection Trunk data for B-ch and D-ch.
Example:(When using 512kbps (8ch) TS as Connection link)
Connection trunk (B-ch)
C_RT: 10 TK: 1-664 CLENS: LEN for the SDT
Connection link (D-ch)
C_RT: 11 TK: 1-8 CLENS: LEN for the FCH
C_RT: 11 TK: 9-16 CLENS: LEN for the SDT
Note:Set the switch on the FCH card depending on the transmission speed.
See...

CHAPTER 5 NDA-24299
Page 100
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 9: ACAN
Assign the CIC number to the connection trunk.
FPC: 1 FCIC: 1-664 CLENS: LEN of the connection trunk
STEP 10: AFCD
Assign NAILED DOWN CONNECTION for the connection link established between FCCH and
SDT.
LENS-A: LEN of SDT EAD-A: 07 (pad off)
LENS-B: LEN of FCCH EAD-B: 07 (pad off)
7.3 Flexible Routing - Fusion
A Fusion trunk call can be routed via “non-Fusion” trunk (C.O. or Tie Line), if the Fusion...

NDA-24299 CHAPTER 5
Page 101
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
The example data setting is shown using Figure 5-44, on condition that CCIS link data has already been
assigned between FPC2 (PC2) and PC3 nodes.
Figure 5-44   FCCS - CCIS Coexisting Network
The following data setting must be assigned at FPC1 (PC1) node in the example.
STEP 1: ASYD
Assign the OPC (Originating Point Code) within the range 1-16383.
Index 180, 181:
Ex.) OPC=16
Miscellaneous Data
Index 186:
b6 must be...

CHAPTER 5 NDA-24299
Page 102
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 4: AMND
Assign MND (Maximum Necessary Digits) including the access code
DC=752 MND=6
STEP 5: ARNPL
Assign the access code to the logical route of speech path. It is not required to assign this data to the
logical route of signal controlling channel and dummy route.
LGRT=1 ACC=75
STEP 6: ARNP
Enter “RT=0” for the self-office code (self-office identification code) in Open Numbering Network.
This number is used...

NDA-24299 CHAPTER 5
Page 103
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 9: ADPCL
Assign the destination PC (Point Code) on speech channel route (Logical Route) basis.
LGRT=1 PC=3
STEP 10: ACSCL
Assign the CSC Group Number (CSCG) for designating the Dch and the location of the CCH, in
cooperation with the FPC of the node that is connected to CCIS link.
STEP 11: ACIC1
Assign the data to establish the relation between Point Code of the destination node and CSCG (CSC
Group) of the...

CHAPTER 5 NDA-24299
Page 104
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
Figure 5-45   External Router - Overview
Figure 5-46   Hardware Connections for External Router
Intern et/
Intran et
FCCS link
 
Speech Data for Fusion
Router
Router Node A
Node B
Signaling data
DTIDTIFusion
     N etw o rk
FCCS signaling is exchanged via the Internet/Intranet.
HUB
Speech
ROUTER
signaling
CPUPBX
FCHFCH
FGHDTI
HUB
LANI
10BASE-T
ACRD 
ACTK 
AFCH 
AFPCACRD 
ACTK 
AGIP 
AETH
D T I: D ig ita l T run k In...

NDA-24299 CHAPTER 5
Page 105
Revision 1.0
DATA PROGRAMMING
Assignment of FCH Related Data
Switch Setting on FCH/FGH Cards:
Set the switches on the FCH/FGH (PA-FCHA) cards as shown below.
 
Figure 5-47   Switch Setting on FCH/FGH (PA-FCHA) Card
STEP 1: ACRD
Assign Route Class Data of Speech Route, FCH, FGH routes, respectively. A sample data assignment
is shown below.
See 6.1 Assignment of Connection Route/Trunk Data for more detailed information.
SW14
Refer to Table 4-3.
1234
OFF
1234
OFF
1234 5678
OF F...