NEC Neax 2400 Imx System Operations And Maintenance Manual

CHAPTER 8 NDA-24238
Page 554
Revision 3.0
MAINTENANCE COMMANDS
DLSL:Display of Lockout Station - LENS
1. Functional Outline
This command prints the LENS of stations in lockout state.
2. Parameters
Input data
Type: Type of Printout (1-3)
1=Printout of all LEN in lockout
2=Printout of locked out LEN in the designated Module Group
3=Printout of locked out LEN in the designated Unit
MG:
Note 1, Note 2
UNIT:Note 2
Note 1:
The parameter is valid only when Type=2.
Note 2:The parameter is valid only when...

NDA-24238 CHAPTER 8
Page 555
Revision 3.0
MAINTENANCE COMMANDS
DLSS:Display of Lockout Station - Number
1. Functional Outline
This command prints the stations in lockout state by station number.
2. Parameters
Input data
Type: Type of Printout (1-3)
1=Printout of all lockout stations
2=Printout of lockout stations by tenant
3=Printout of lockout stations within a specified range of station number.
TN:
Note 1, Note 2
Start STN: Maximum 6 digitsNote 2
End STN: Maximum 6 digitsNote 2
Note 1:
The parameter is...

CHAPTER 8 NDA-24238
Page 556
Revision 3.0
MAINTENANCE COMMANDS
DLSS_T:Display of Lock Out Station – Number – Telephone Number
1. Functional Outline
This command is used to print out stations in lockout state, by using Telephone Numbers. This command is
available at NCN (for Fusion network) only. 
2. Parameters
Input Data
TYPE: Printout of all lockout stations
Printout of lockout stations by tenant
Printout of lockout stations within a specified range of station number
UGN: User Group Number 
Note 1, Note...

NDA-24238 CHAPTER 8
Page 557
Revision 3.0
MAINTENANCE COMMANDS
DLTEL:Display of Telephone Number from LENS for LDM
1. Functional Outline
This command, available at each Local Node (LN), is used to display the Telephone Number or other station
data by designating a specific LEN.
2. Parameters
Input Data
LENS: Line Equipment Number [6 digits]
Display Data
UGN: User Group Number
TELN: Telephone Number [Max. 16 digits]
TN: Tenant Number
STN: Station Number [Max. 6 digits]
TEC: Telephone Equipment Class...

CHAPTER 8 NDA-24238
Page 558
Revision 3.0
MAINTENANCE COMMANDS
DNTEL:Display of Telephone Number from LENS for NDM
1. Functional Outline
This command, available at Network Control Node (NCN) only, is used to display the Telephone Number or
other station data by designating a specific FPC and LEN.
2. Parameters
Input Data
FPC: Fusion Point Code [1-253]
LENS: Line Equipment Number [6 digits]
Display Data
UGN: User Group Number
TELN: Telephone Number [Max. 16 digits]
NID: Network ID 
Note
TN: Tenant Number...

NDA-24238 CHAPTER 8
Page 559
Revision 3.0
MAINTENANCE COMMANDS
DPKG:Display of Setting Port Package
1. Functional Outline
This command is used to display the circuit card name accommodated in each Group of a specific UNIT.
Note:When using this command, make sure that each circuit card related database files have already been
installed to your MAT. (See FLINST command for more information.)
2. Parameters
Input Data
MG: Module Group (MG) number [00-07]
UNIT: Unit (U) number [0-3]
Buttons
Get: Click to get...

CHAPTER 8 NDA-24238
Page 560
Revision 3.0
MAINTENANCE COMMANDS
DPSW:Display Package Switch Status
1. Functional Outline
This command is used to display the following information on a Line/Trunk or Control circuit card:
[When MAT is in On-Line Mode (=connected to the system)]
 Current status of each switch
 Explanation of each switch function
[When MAT is in Off-Line Mode (= not connected to the system)]
 Explanation of each switch function
Note 1:When using this command, make sure that each circuit...

NDA-24238 CHAPTER 8
Page 561
Revision 3.0
MAINTENANCE COMMANDS
DSTN:Display of Station Data
1. Functional Outline
This command is used to display the registered Station Data corresponding to the designated Tenant and
Station Number. In addition, the information of Hot Line, D
term Key Layout, Hunting, and Call Pickup, etc,
can also be displayed as the data related to the designated stations.
2. Parameters
Input Data
TN: Tenant Number
STN: Station Number [0-9, #, * (Max. 6 digits)]
Buttons
[For display...

CHAPTER 8 NDA-24238
Page 562
Revision 3.0
MAINTENANCE COMMANDS
DTELN:Display of Telephone Number Data for NDM
1. Functional Outline
This command is used to display the registered station data corresponding to specified User Group Number
(UGN) and Telephone Number (TELN). The following data related to Number Group can be displayed by
clicking the selection button for each data. This command can be used only when logging in to Network
Control Node (NCN).
 ACPGN: Call Pickup Group (NDM)
 ACPEN: Call...

NDA-24238 CHAPTER 8
Page 563
Revision 3.0
MAINTENANCE COMMANDS
Selection Button
CPGN: Call Pickup Group (NDM)
CPEN: Call Pickup Expand Group (NDM)
SHUN: Station Hunting Group-UCD (NDM)
SHCN: Station Hunting Group-Circular (NDM)
HLSN: Hot Line Station (NDM)
SHPN: Station Hunting Group-Pilot (NDM)
KYD: Key Data for D
term