NEC Neax 2400 Imx System Operations And Maintenance Manual

CHAPTER 8 NDA-24238
Page 524
Revision 3.0
MAINTENANCE COMMANDS
AT R F :Assignment of Traffic Measurement Order
1. Functional Outline
This command is used to assign and delete traffic measurement programs. A request for traffic measurement
is performed when a traffic measurement instruction has been assigned by this command. The collected traffic
measurement data can be stored on the HD of the MAT, which can be designated on the basis of traffic
measurement type.
2. Parameters
Input Data
TYPE: Type of...

NDA-24238 CHAPTER 8
Page 525
Revision 3.0
MAINTENANCE COMMANDS
ATRFN:Assignment of Traffic Measurement Order for Fusion Network
1. Functional Outline
This command is used to assign and delete traffic measurement programs available on the Ethernet. A request
for traffic measurement is performed on a network basis when a traffic measurement instruction has been
assigned by this command. The collected traffic measurement data can be stored on the HD of the MAT
(connected to the NCN: Network Control Node),...

CHAPTER 8 NDA-24238
Page 526
Revision 3.0
MAINTENANCE COMMANDS
BOSD:Back Up One-Touch Speed Call Memory Data
1. Functional Outline
 Save Function
 Saves the data residing in the One-Touch Speed Call Memory of DLC/ELC card onto a floppy disk.
 Verify Function
 Verifies the One-Touch Speed Call Memory data saved on the floppy disk with the data residing in the
One-Touch Speed Call Memory of DLC/ELC card.
 Load Function
 Loads the One-Touch Speed Call Memory data saved in the floppy disk into the...

NDA-24238 CHAPTER 8
Page 527
Revision 3.0
MAINTENANCE COMMANDS
CADSD:Continuous Assignment of Station Data
1. Functional Outline
This command can assign/delete many station data simultaneously which have consecutive numbers.
2. Parameters
Input Data
Type: Assign/Delete
[When Assign is selected in the Type selection list box]
TN(START): Start Tenant Number
TN(END): End Tenant Number
STN(START): Start Station Number [Max. 6 digits] 
Note 1
STN(END): End Station Number [Max. 6 digits] Note 1
STEP: Station...

CHAPTER 8 NDA-24238
Page 528
Revision 3.0
MAINTENANCE COMMANDS
TEC: Telephone Equipment Class [1-31]
1=DP (10pps) 2=PB
3=DP/PB 4=DP (20pps)
5-11=Not used 12=D
term
13=Data Terminal via Dterm14=Hot Line
15=CAS Line 16=Data Terminal via Data Module
17=Not used 18=Virtual Line Appearance (for D
term Multi-Line)
19-22=Not used 23=ISDN Terminal
24-26=Not used 27=8 Conference Equipment
28-31=Not used
RSC: Route Restriction Class [0-15]
SFC: Service Feature Class [0-15]
Buttons
Execute: Click to make the input...

NDA-24238 CHAPTER 8
Page 529
Revision 3.0
MAINTENANCE COMMANDS
When Delete is selected in the Type selection list box
Input Data
TN(START): First Tenant Number
TN(END): Last Tenant Number
STN(START): First Station Number [Max. 6 digits]
STN(END): Last Station Number [Max. 6 digits]
STEP: Station Count-up Step 
Note 1
If using * and # → [1-12]
If not using * and # → [1-10]
Note 1:In this parameter, specify the size of increment between the consecutive station numbers to be deleted.
See the example below:...

CHAPTER 8 NDA-24238
Page 530
Revision 3.0
MAINTENANCE COMMANDS
CATK:Continuous Assignment of Trunk Data
1. Functional Outline
This command can assign/delete many trunk data simultaneously which have consecutive numbers.
2. Parameters
Type/KIND (
Note): Assign/Delete
Note:Type (for software Release 6 or earlier)
KIND (for software Release 7 or later)
When “Assign” is selected in the “Type/KIND” selection list box
Input Data
RT: R o u t e  N u m b e r
TK (START): First Trunk Number [1-768]
TK (END): Last...

NDA-24238 CHAPTER 8
Page 531
Revision 3.0
MAINTENANCE COMMANDS
Buttons
Execute: Click to make the input data valid.
Cancel: Click to cancel the input data.
Exit: Click to exit this command.
Display Data
TK: Assigned Trunk Number
LENS: Line Equipment Number
STATUS: Data Entry Result
OK=Data Assignment is successful 
Note 4
Note 4:
If not OK (i.e. the data entry is not successful), related error message is displayed here. 

CHAPTER 8 NDA-24238
Page 532
Revision 3.0
MAINTENANCE COMMANDS
When “Delete” is selected in the “Type/KIND” selection list box
Input Data
RT: R o u t e  N u m b e r
TK(START): First Trunk Number [1-768]
TK(END): Last Trunk Number [1-768]
STEP: Trunk Count-up Step [1-10] 
Note 1
Buttons
Execute: Click to delete the input data.
Cancel: Click to cancel the deletion.
Exit: Click to exit this command.
Display Data
TK: Trunk Number
STATUS: Result of Deletion
OK=Deletion Success 
Note 2
Note 1:
In this...

NDA-24238 CHAPTER 8
Page 533
Revision 3.0
MAINTENANCE COMMANDS
Details on Trunk Arrangement TYPE
When assigning the consecutive trunk data by using the CATK command, you must select the trunk
arrangement type (1-6) in the TYPE parameter. The following are examples of accommodated 16 COT circuit
cards:
TYPE=1 (Level → Group → Unit)
Trunk data is arranged in the following numerical order.
U=2
00
PIM C/EU=3
05 10 15 20
16
C
O16
C
O16
C
O
16
C
O16
C
O 16
C
O
PIM C/E
U=0U=1
TTT
T T T
LV 7
LV 6
LV 5
LV 4
LV 3...