NEC Neax 2400 Imx System Operations And Maintenance Manual

CHAPTER 8 NDA-24238
Page 594
Revision 3.0
MAINTENANCE COMMANDS
MBCT:Make Busy of Connection Trunk for LDM
1. Functional Outline
This command is used to set/reset the make busy state of the connection trunk.
2. Parameters
Input Data
C_RT: Connection Route Number [1-1023]
C_TK: Trunk Number [1-4095]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy (Outgoing) 

NDA-24238 CHAPTER 8
Page 595
Revision 3.0
MAINTENANCE COMMANDS
MBLE:Make Busy of LENS
1. Functional Outline
This command assigns the IDLE/BUSY status of Line Equipment Numbers (LENS).
2. Parameters
Input data
LENS
MB: 0=Make Idle
1=Make Busy 

CHAPTER 8 NDA-24238
Page 596
Revision 3.0
MAINTENANCE COMMANDS
MBPM:Make Busy of Port Microprocessor
1. Functional Outline
This command sets or resets the make-busy state of the circuit card that contains the port microprocessor. This
setting and resetting is performed individually for each circuit card. If the location of the circuit card containing
the port microprocessor is specified in this command, the operating state of all circuit cards mounted in the
associated unit is displayed.
2. Parameters...

NDA-24238 CHAPTER 8
Page 597
Revision 3.0
MAINTENANCE COMMANDS
MBRT:Make Busy of Route
1. Functional Outline
This command assigns Idle/Busy status for all the trunks in the route designated.
2. Parameters
Input data
RT: Route Number of the external route/internal route. Ta b l e  8 - 6 provides the meaning of
the internal route numbers.
MB: 0=Make Idle
1=Make Busy
Table 8-6  Route Number Explanation
DATA MEANING DATA MEANING
901 Attendant/Desk Console 902 Originating Register Trunk
903 Incoming Register...

CHAPTER 8 NDA-24238
Page 598
Revision 3.0
MAINTENANCE COMMANDS
MBSM:Make Busy of System Message Printout
1. Functional Outline
This command allows or inhibits the system message printer to output system messages.
2. Parameters
Input data
PORT NO.: Port Number of the printer
MB: 0=Make Idle
1=Make Busy 

NDA-24238 CHAPTER 8
Page 599
Revision 3.0
MAINTENANCE COMMANDS
MBST:Make Busy of Station
1. Functional Outline
This command assigns the Idle/Busy status of stations.
2. Parameters
Input data
TN
STN: Maximum 5 digits for Business system/Maximum 6 digits for Hotel system.
MB: 0=Make Idle
1=Make Busy 

CHAPTER 8 NDA-24238
Page 600
Revision 3.0
MAINTENANCE COMMANDS
MBST_T:Make Busy of Station – Telephone Number
1. Functional Outline
This command is used to assign the IDLE/BUSY status of stations, by using Telephone Numbers. This
command is available at NCN (for Fusion network) only. 
2. Parameters
Input Data
UGN: User Group Number
TELN: Telephone Number (max. 16 digits) 
MB: Make Busy/Make Idle
Display Data
FPC: Fusion Point Code (1-253)  
Note
TN: Tenant Number Note
STN: Physical Station Number 
(max....

NDA-24238 CHAPTER 8
Page 601
Revision 3.0
MAINTENANCE COMMANDS
MBTC:Make Busy of Trunk-Continuous
1. Functional Outline
This command is used to assign the IDLE/BUSY status of trunks. By using this command, plural trunks can
be placed into IDLE/BUSY state simultaneously per a route designated in “RT” parameter.
2. Parameters
Input Data
RT: R o u t e  N u m b e r
TK: Trunk Number 
Note 1
MB: 0=Make Idle
1=Make Busy (Outgoing)
2=Make Busy (Bothway) 
Note 2
Note 1:
Multiple trunks can be assigned...

CHAPTER 8 NDA-24238
Page 602
Revision 3.0
MAINTENANCE COMMANDS
MBTK:Make Busy of Trunk
1. Functional Outline
This command assigns the Idle/Busy status of trunks.
2. Parameters
RT: R o u t e  N u m b e r
TK: Trunk Number
MB: 0=Make Idle
1=Make Busy (Outgoing) 

NDA-24238 CHAPTER 8
Page 603
Revision 3.0
MAINTENANCE COMMANDS
MEM_HDD:Data Control Between Memory and HDD
1. Functional Outline
This command is used to save the following data from MEM of PBX to HDD of PBX, and vice versa.
2. Parameters
Input data
Direction Select: Memory to Hard Disk
Hard Disk to Memory
Verify HDD against MEM
Data Type Selection: Data Memory
Note 1
Name Display
Wireless Call Forwarding
Call Forwarding
Speed Calling
User Assign Soft Key 
Number Sharing 
Note 2
Call Block 
ACD Data...