NEC Neax 2400 Imx System Operations And Maintenance Manual

CHAPTER 8 NDA-24238
Page 604
Revision 3.0
MAINTENANCE COMMANDS
MEM_HDD_N:Data Control Between Memory and HDD for NDM
1. Functional Outline
This command, available at the NCN only, is used to save/verify a series of Office Data from the Memory of
all Local Nodes to the HDD of each same node. 
2. Parameters
Input data
Direction Select: MEM to HDD
Verify HDD against MEM
Data Type Selection: Data Memory
Note 1
Name Display
Wireless Call Forwarding
Call Forwarding
Speed Calling
User Assign Soft Key 
Number...

NDA-24238 CHAPTER 8
Page 605
Revision 3.0
MAINTENANCE COMMANDS
MFCH:Make Busy of FCCH
1. Functional Outline
This command is used to set or reset the make busy state of the FCH card.
2. Parameters
Input Data
FCHN: FCH Number [1-255]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy 

CHAPTER 8 NDA-24238
Page 606
Revision 3.0
MAINTENANCE COMMANDS
PMBU:Port Microprocessor Back Up
1. Functional Outline
This command saves the contents of Port Microprocessor (PM) onto Floppy Disk (FD) or verifies them.
Information of firmware (Program Code) also appears on the screen.
2. Parameters
Input data
Direction Select: Port Microprocessor to MAT
Verify Port Microprocessor
Verify PM with Error List Auto Verify Afterward can be performed when desig-
nating Port Microprocessor to MAT.
PM Information:...

NDA-24238 CHAPTER 8
Page 607
Revision 3.0
MAINTENANCE COMMANDS
RALM:Release Alarm
1. Functional Outline
This command clears the fault indications.
2. Parameters
Input data
WRT: Y=Alarm is released
N=Not released
RETURN TO MENU?: Y=Return to MENU
N=Start operation again
Display data
Alarms Released 

CHAPTER 8 NDA-24238
Page 608
Revision 3.0
MAINTENANCE COMMANDS
RALMN:Release Alarm for NDM
1. Functional Outline
This command, available at the NCN only, clears the fault indications of all the Nodes by clicking the release
button on the display. 
2. Parameters
Display data
FPC: FPC of alarm released Nodes
Status: Result of releasing the alarm
OK/NG 

NDA-24238 CHAPTER 8
Page 609
Revision 3.0
MAINTENANCE COMMANDS
RLST:Release Station/Trunk
1. Functional Outline
This command releases a station or trunk.
2. Parameters
Input data
TYPE: Type of Select (1-4)
1=Stations
2=Trunk
3=LENS
4=Connection Trunk
TN:
Note 1
STN: Maximum 6 digits  Note 1
RT:Note 2
TK:Note 2
LENS:Note 3
Connection RT: (1-1023)  Note 4
Connection TK: (1-4095) Note 4
Note 1:
This parameter is valid only when TYPE=1.
Note 2:This parameter is valid only when TYPE=2.
Note 3:This parameter...

CHAPTER 8 NDA-24238
Page 610
Revision 3.0
MAINTENANCE COMMANDS
RLST_T:Release of Station/Trunk – Telephone Number
1. Functional Outline
This command is used to release a station/trunk, by using Telephone Numbers. This command is available at
NCN (for Fusion network) only. 
2. Parameters
Input Data
TYPE: Telephone Number
Trunk
LENS
Connection Trunk
UGN: User Group Number 
Note 1
TELN: Telephone Number (max. 16 digits)Note 1
RT: External/Internal Route Number Note 2
TK: Trunk Number Note 2
LENS: Line...

NDA-24238 CHAPTER 8
Page 611
Revision 3.0
MAINTENANCE COMMANDS
STATUS: Status of Station/Trunk (1-5)
1=Idle
2=Busy
3=Lockout
4=Make Busy
5=Now Calling
INFORMATION: Information on the connected party 
Note 6
ERN: Area Number (1-32) Note 7
GRN: Group Number (1-8) Note 7
CSN/ZTN: CS/ZT Number (1-32) Note 7
PCN: PHS Community Number (1-1024) Note 7
Note 6:
This data is displayed when “STATUS” =2 (Busy).
Note 7:This data is for Wireless System only.
Buttons
Get: Click to get information on the station/trunk....

CHAPTER 8 NDA-24238
Page 612
Revision 3.0
MAINTENANCE COMMANDS
SINZ:System Initialization
1. Functional Outline
This command initializes the PBX from the MAT. At the time of system initialization, this command allows
the programs and the office data to be loaded from a Hard Disk of PBX into the RAM of PBX.
2. Parameters
Input data
TYPE: Kind of Initialization (1-4)
1=System Initialize
2=System Initialize Office Data Load & System Initialize
3=System Initialize Program Load & System Initialize
4=System...

NDA-24238 CHAPTER 8
Page 613
Revision 3.0
MAINTENANCE COMMANDS
SPTS:Scanning of Port Status
1. Functional Outline
This command displays momentarily the working status of Port Microprocessor (PM) on Module Group (MG),
Unit, and Group basis.
2. Parameters
Input data
MG
Unit
Group
Interval: Unit for this parameter is in seconds.
Entry Procedure
Type 1: By MG
Display of Scanning by Designating MG (Figure 8-1)
Package Status PM: Not Mounted 
Note
ID: Idle at least one
BY: All Busy
MB: Under Make Busy Status...