NEC Neax 2400 Imx Hotel Features And Specifications

NEAX2400 IMX Hotel Features and Specifications
NDA-24245, Issue 2
Page 109
Maid Status M-22
M-22 Maid Status
General Description
This feature allows the Console, Special Administration, or guest room stations to update the status of guest room
conditions. This information is stored in the NEAX2400 IMX Hotel Processor (HP) for printout services, and is
forwarded to the PMS computer for readout. AUDIT REPORTS [A-26] of MAID STATUS are also available. Refer
to the AUDIT REPORTS [A-26] feature description...

NEAX2400 IMX Hotel Features and Specifications
Page 110NDA-24245, Issue 2
M-22 Maid Status
Operating Procedure (cont’d)
Note:
 If a Dterm is used for a guest station, the following will display:
Note 1:
Reorder tone will be heard instead of service set tone if this feature is not accepted by the NEAX2400 IMX.
Note 2:
Service set tone will be heard after the Maid Status access code is dialed, if the Maid ID code is not in service.
Note 3:
If the Maid ID code is not in service, the following will be...

NEAX2400 IMX Hotel Features and Specifications
NDA-24245, Issue 2
Page 111
Maid Status M-22
Service Conditions (cont’d)
2. MAID STATUS information from the Console, guest phones, or the Special Administration Station is sent
to the PMS for readout.
3. A maximum of six digits can be used for the identification code (specific maid, repairman, Special
Administration Station). Use of ID codes is optional, and is left to the customers discretion.
4. When setting this service from a guest room or Special...

NEAX2400 IMX Hotel Features and Specifications
Page 112NDA-24245, Issue 2
M-51 Manual Switching Of C.O. Incoming Call Destination
M-51  Manual Switching Of C.O. Incoming Call 
Destination
General Description
This feature allows the Console operator to manually change the termination point of a specific group of trunks.
Trunks that normally are used as DIT trunks may be changed to terminate at the Console.
Operating Procedure
To change the termination of DIT trunks from stations to the Console:
To...

NEAX2400 IMX Hotel Features and Specifications
NDA-24245, Issue 2
Page 113
Maid Status - Answerback M-68
M-68  Maid Status - Answerback
General Description
This feature allows a maid or other hotel personnel to receive answerback acknowledgment from the PMS (Property
Management System) computer when MAID STATUS has been changed using guest room station or Special
Administration Station telephones.
Operating Procedure
Service setting from a guest room station by a maid or repairman:
Note:
In case of...

NEAX2400 IMX Hotel Features and Specifications
Page 114NDA-24245, Issue 2
O-6 Off-hook Alarm
O-6 Off-hook Alarm
General Description
The OFF-HOOK ALARM feature is intended for emergency alert situations. A station user who remains off-hook
without dialing for longer than 30 seconds is automatically routed to the EMG key on the Console or to a
predesignated station.
Operating Procedure
Service Conditions
1. Under CALL HOLD [C-6] or CONSULTATION HOLD – ALL CALLS [C-17] mode, the OFF-HOOK
ALARM service...

NEAX2400 IMX Hotel Features and Specifications
NDA-24245, Issue 2
Page 115
Overtime Call O-9
O-9 Overtime Call
General Description
The OVERTIME CALL feature permits the system to measure the length of all outgoing calls, and to print a
message on the hotel printer or alert the Console that the call has exceeded a predetermined time.
Operating Procedure
If the hotel printer is to receive this information, no manual operation is required.
To operate from the Console:
Service Conditions
1. If the OVERTIME...

NEAX2400 IMX Hotel Features and Specifications
Page 116NDA-24245, Issue 2
P-8 Printer Control – Hotel Attendant Console
P-8  Printer Control – Hotel Attendant Console
General Description
A printer should be connected to the NEAX2400 IMX to provide AUDIT REPORTS [A-26], CHECK-IN/
CHECKOUT [C-23], OVERTIME CALL [O-9], and AUTOMATIC WAKE-UP [A-10] set times, and results of
Wake-Up calls. In the event that PMS is provided and then temporarily fails, PMS messages will be sent to this
printer.
Printer Service...

NEAX2400 IMX Hotel Features and Specifications
NDA-24245, Issue 2
Page 117
PMS Interface – BISYNC P-27
P-27  PMS Interface – BISYNC
General Description
The PMS INTERFACE service feature provides an interface to the Property Management System (PMS) computer
using the standard IBM® BISYNC (Binary Synchronous Communication) protocol. This interface allows a PMS
computer to accommodate both front and back office hospitality management features.
Note:
IBM® is a registered trademark of International Business...

NEAX2400 IMX Hotel Features and Specifications
Page 118NDA-24245, Issue 2
P-29 PMS Interface
P-29 PMS Interface
General Description
The PMS INTERFACE provides a data link between the NEAX2400 IMX and the customers Property Management
System (PMS) computer. This communications link enables the PMS-related hospitality management functions.
Major functions and their communication interactions are indicated below:
AUTOMATIC WAKE-UP  [A-10] IMX PMS
AUTOMATIC MESSAGE WAITING LAMP OFF  [A-48] IMX PMS...