NEC Neax 2000 Ivs2 Remote Pim System Manual
Here you can view all the pages of manual NEC Neax 2000 Ivs2 Remote Pim System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 81
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIA (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 73 SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW2 (DIP SW) 1ONControl channel signaling data transmission speed: 48 kbps Control channel signaling data transmission speed: 64 kbps 2ONDTI frame configuration: 12-Multi Frame DTI frame configuration: 24-Multi Frame 3ON Line code: AMI with ZCS Line code: B8ZS 4ONSetting of control signal time slot NOTE 4, NOTE 5 5ON 6ON 7...
Page 82
NEAX2000 IVS2 Remote PIM System ManualPage 74 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIA (DAI) The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1:Set the groove on the switch to the desired position. NOTE 2:When the power is on, flip the MB switch to ON (UP position) before...
Page 83
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIA (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 75 NOTE 3:When the source clock signal is supplied via the line between the Main Site and the Remote Site, set the SW1-1 and SW1-2 as indicated in the following table. In this case, DAIA cards (DAIA0, DAIA1) must be mounted in PIM0. NOTE 4:Time Slot Number 0, 20, 21, and 22 (TS0/20/21/22) cannot be used for control signal. NOTE 5:This setting must be identical with the opposite DAIB...
Page 84
NEAX2000 IVS2 Remote PIM System ManualPage 76 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIB (DAI) PN-DAIB (DAI) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally LINK Green Remains lit when a link between this card and a distant office is normally connected Goes out after 15 seconds of link disconnection RED Red Remains lit when detecting PCM signal loss or Frame Alignment...
Page 85
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIB (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 77 Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENSE (Rotary SW) 0-FAlways set to 0 1-F Not used MB (Toggle SW) NOTE 1 UP For make-busy For normal operation SW1 (Piano Key SW)1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4 Always set to OFF (Continued) 0 ON DOWN 4 3 2 1 OFF ON OFF OFF OFF OFF
Page 86
NEAX2000 IVS2 Remote PIM System ManualPage 78 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIB (DAI) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW2 (DIP SW) 1ONControl channel signaling data transmission speed: 48 kbps Control channel signaling data transmission speed: 64 kbps 2ONDTI frame configuration: 12-Multi Frame DTI frame configuration: 24-Multi Frame 3ON Line code: AMI with ZCS Line code: B8ZS 4ONSetting of control signal time slot NOTE 2, NOTE 3 5ON 6ON 7 OFF...
Page 87
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIB (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 79 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1:When the power is on, flip the MB switch to ON (UP position) before plugging/unplug- ging the circuit card. NOTE 2:Time...
Page 88
NEAX2000 IVS2 Remote PIM System ManualPage 80 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIC (DAI) PN-DAIC (DAI) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally LINK Green Remains lit when the following connections are normal: Control channel link between the DAIA card and DAIB card Connection between the opposite DAIC card Goes out after 15 seconds of link disconnection...
Page 89
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIC (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 81 Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK MB (Toggle SW) NOTEUP For make-busy For normal operation SW1 (Piano Key SW)1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4 Always set to OFF SW2 (DIP SW) 1 Not used 2ONDTI frame configuration: 12-Multi Frame DTI frame configuration: 24-Multi Frame 3ON Line code: AMI with ZCS Line code: B8ZS 4...
Page 90
NEAX2000 IVS2 Remote PIM System ManualPage 82 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIC (DAI) The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE:When the power is on, flip MB switch to ON (UP position) before plugging/unplugging the circuit card. SW3 (DIP SW) 1Set the...