NEC Neax 2000 Ivs2 Remote Pim System Manual

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAID (DAI)
NEAX2000 IVS2 Remote PIM System Manual    
ND-70917 (E), Issue 1.0   Page 83
PN-DAID (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally
LINK Green Remains lit when a link between this card and a distant office is
normally connected
Goes out after 15 seconds of link disconnection
RMT Red Remains lit when receiving the alarm signal from a distant...

 NEAX2000 IVS2 Remote PIM System ManualPage 84  ND-70917 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAID (DAI)
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 1
0-FFP (Firmware Processor) Number setting for the
DA I D c ard
By this setting, the system regards the DAID card
and the opposite DAIE card as one Firmware Pro-
cessor.
0 Not used
1FP No. 1
2FP No. 2
3FP No. 3
4-F Not used
MB (Toggle SW)
NOTE 2
UP For make-busy
For normal operation
SW1...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAID (DAI)
NEAX2000 IVS2 Remote PIM System Manual    
ND-70917 (E), Issue 1.0   Page 85
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48 kbps
Control channel signaling data 
transmission speed: 64 kbps
2ONCRC Synchronization Detection 
Timer is provided.
CRC Synchronization Detection 
Timer is not provided.
3ON CRC4 Check is provided.
CRC4 Check is not provided.
(Continued)
1
23
45
67...

 NEAX2000 IVS2 Remote PIM System ManualPage 86  ND-70917 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAID (DAI)
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SW2 (DIP SW)
4Setting of control signal time slot
NOTE 4, NOTE 5 OFF
5
OFF
6
OFF
7
OFF
8ON
(Continued)
1
23
45
67
8ON
ON
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFFONONONON TS1
ON OFF ON ON ON TS2
OFF OFF ON ON ON TS3
ON ON OFF ON ON TS4
OFF ON OFF ON ON TS5
ON OFF OFF ON ON TS6
OFF OFF OFF ON ON TS7
ON ON ON OFF ON TS8
OFF ON ON OFF...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAID (DAI)
NEAX2000 IVS2 Remote PIM System Manual    
ND-70917 (E), Issue 1.0   Page 87
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON (UP position)...

 NEAX2000 IVS2 Remote PIM System ManualPage 88  ND-70917 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAID (DAI)
NOTE 3:When the source clock signal is supplied via the line between the Main Site and the
Remote Site, set the SW1-1 and SW1-2 as the following table. In this case, DAID cards
(DAID0, DAID1) must be mounted in PIM0.
NOTE 4:Time Slot Number 0 and 28 (TS0/28) cannot be used for control signal.
NOTE 5:This setting must be identical with the opposite DAIE card.
CONDITIONSDAI D0 DAID 1...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAIE (DAI)
NEAX2000 IVS2 Remote PIM System Manual    
ND-70917 (E), Issue 1.0   Page 89
PN-DAIE (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally
LINK Green Remains lit when a link between this card and a distant office is
normally connected
Goes out after 15 seconds of link disconnection
RMT Red Remains lit when receiving the alarm signal from a distant...

 NEAX2000 IVS2 Remote PIM System ManualPage 90  ND-70917 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAIE (DAI)
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE 
(Rotary SW)
0-FAlways set to 0
1-F
Not used
MB (Toggle SW)
NOTE 1
UP
For make-busy
For normal operation
SW1 
(Piano Key SW)1
Always set to OFF
2
Always set to OFF
3
Always set to OFF
4
Always set to OFF
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48 kbps
Control channel signaling...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAIE (DAI)
NEAX2000 IVS2 Remote PIM System Manual    
ND-70917 (E), Issue 1.0   Page 91
SW2 (DIP SW)
4Setting of control signal time slot
NOTE 2, NOTE 3 OFF
5
OFF
6
OFF
7
OFF
8ON
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
45
67
8ON
ON
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFFONONONON TS1
ON OFF ON ON ON TS2
OFF OFF ON ON ON TS3
ON ON OFF ON ON TS4
OFF ON OFF ON ON TS5
ON OFF OFF ON ON TS6
OFF OFF OFF ON ON TS7
ON ON ON OFF ON TS8
OFF ON...

 NEAX2000 IVS2 Remote PIM System ManualPage 92  ND-70917 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-DAIE (DAI)
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card. 
NOTE 2:Time Slot...