NEC Neax 2000 Ivs2 Remote Pim System Manual
Have a look at the manual NEC Neax 2000 Ivs2 Remote Pim System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAID (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 83 PN-DAID (DAI) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally LINK Green Remains lit when a link between this card and a distant office is normally connected Goes out after 15 seconds of link disconnection RMT Red Remains lit when receiving the alarm signal from a distant office LOOP – Not used PWR Red Remains lit when detecting PCM signal loss BL Red Remains lit while data transmission on control channel (D ch) Remains lit while FP data downloading SRT JPS E1Z JPR SW2 SW3BUS PCM1 PCM0 CNSENSE RUN MB SW1LINK RMT LOOP PWR BL JP
NEAX2000 IVS2 Remote PIM System ManualPage 84 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAID (DAI) Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENSE (Rotary SW) NOTE 1 0-FFP (Firmware Processor) Number setting for the DA I D c ard By this setting, the system regards the DAID card and the opposite DAIE card as one Firmware Pro- cessor. 0 Not used 1FP No. 1 2FP No. 2 3FP No. 3 4-F Not used MB (Toggle SW) NOTE 2 UP For make-busy For normal operation SW1 (Piano Key SW)1 NOTE 3ONFor supplying 2.0 MHz clock to PLO 0 No clock supply to PLO 0 2 NOTE 3ONFor supplying 2.0 MHz clock to PLO 1 No clock supply to PLO 1 3 Always set to OFF 4 Always set to OFF (Continued) 1 32 ON DOWN 4 3 2 1 OFF ON OFF OFF OFF OFF
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAID (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 85 SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW2 (DIP SW) 1ONControl channel signaling data transmission speed: 48 kbps Control channel signaling data transmission speed: 64 kbps 2ONCRC Synchronization Detection Timer is provided. CRC Synchronization Detection Timer is not provided. 3ON CRC4 Check is provided. CRC4 Check is not provided. (Continued) 1 23 45 67 8ON OFF OFF OFF
NEAX2000 IVS2 Remote PIM System ManualPage 86 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAID (DAI) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW2 (DIP SW) 4Setting of control signal time slot NOTE 4, NOTE 5 OFF 5 OFF 6 OFF 7 OFF 8ON (Continued) 1 23 45 67 8ON ON SWITCH NUMBER TIME SLOT NUMBER 45678 OFFONONONON TS1 ON OFF ON ON ON TS2 OFF OFF ON ON ON TS3 ON ON OFF ON ON TS4 OFF ON OFF ON ON TS5 ON OFF OFF ON ON TS6 OFF OFF OFF ON ON TS7 ON ON ON OFF ON TS8 OFF ON ON OFF ON TS9 ON OFF ON OFF ON TS10 OFF OFF ON OFF ON TS11 ON ON OFF OFF ON TS12 OFFONOFFOFFON TS13 ON OFF OFF OFF ON TS14 OFF OFF OFF OFF ON TS15 ON ON ON ON OFF TS16 OFFONONONOFF TS17 ON OFF ON ON OFF TS18 OFF OFF ON ON OFF TS19 ON ON OFF ON OFF TS20 OFF ON OFF ON OFF TS21 ON OFF OFF ON OFF TS22 OFF OFF OFF ON OFF TS23 ON ON ON OFF OFF TS24 OFF ON ON OFF OFF TS25 ON OFF ON OFF OFF TS26 OFF OFF ON OFF OFF TS27 OFF ON OFF OFF OFF TS29 ON OFF OFF OFF OFF TS30 OFF OFF OFF OFF OFF TS31 ON ON ON OFF
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAID (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 87 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1:Set the groove on the switch to the desired position. NOTE 2:When the power is on, flip the MB switch to ON (UP position) before plugging/unplug- ging the circuit card. SW3 (DIP SW) 1 Always set to ON 2 Always set to ON 3 Always set to ON 4 Always set to OFF JPS (Jumper Pin) Balanced transmission: 120 ohms (for twisted-pair cable) LeftTA is grounded on the transmission line: 75 ohms (for coaxial cable) JPR (Jumper Pin) Balanced transmission: 120 ohms (for twisted-pair cable) LeftRA is grounded on the transmission line: 75 ohms (for coaxial cable) E1Z (Jumper Pin) Line impedance: 120 ohms (for twisted-pair cable) LeftLine impedance: 75 ohms (for coaxial cable) SRT (Jumper Pin) Right For mounting this card on PIM0 LeftFor mounting this card on PIM1- PIM7 JP (Jumper Pin) Line impedance: 120 ohms (for twisted-pair cable) DOWNLine impedance: 75 ohms (for coaxial cable) (Continued) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 4ON ON ON ON ON Right Right Right UP
NEAX2000 IVS2 Remote PIM System ManualPage 88 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAID (DAI) NOTE 3:When the source clock signal is supplied via the line between the Main Site and the Remote Site, set the SW1-1 and SW1-2 as the following table. In this case, DAID cards (DAID0, DAID1) must be mounted in PIM0. NOTE 4:Time Slot Number 0 and 28 (TS0/28) cannot be used for control signal. NOTE 5:This setting must be identical with the opposite DAIE card. CONDITIONSDAI D0 DAID 1 DAID2 REMARKS SW 1-1SW 1-2SW 1-1SW 1-2SW 1-1SW 1-2 One DAID card is provided.ON OFF – – – –Clock signal is sent to PLO0 of MP card via Supply Route 0 (DAID0). Two or three DAID cards are provided.ON OFF OFF ON OFF OFFClock signal supply route automatically changes to Route 1 (DAID1), if a transmis- sion line failure occurs on Supply Route 0.
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIE (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 89 PN-DAIE (DAI) Location of Lamps, Switches, and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally LINK Green Remains lit when a link between this card and a distant office is normally connected Goes out after 15 seconds of link disconnection RMT Red Remains lit when receiving the alarm signal from a distant office LOOP – Not used BL Red Remains lit while data transmission on control channel (D ch) Remains lit while FP data downloading JPS JPR E1Z SW2 SW3BUS CNSENSE RUN MB SW1LINK RMT LOOP BL JP
NEAX2000 IVS2 Remote PIM System ManualPage 90 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIE (DAI) Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENSE (Rotary SW) 0-FAlways set to 0 1-F Not used MB (Toggle SW) NOTE 1 UP For make-busy For normal operation SW1 (Piano Key SW)1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4 Always set to OFF SW2 (DIP SW) 1ONControl channel signaling data transmission speed: 48 kbps Control channel signaling data transmission speed: 64 kbps 2ONCRC Synchronization Detection Timer is provided. CRC Synchronization Detection Timer is not provided. 3ON CRC4 Check is provided. CRC4 Check is not provided. (Continued) 0 ON DOWN 4 3 2 1 OFF ON OFF OFF OFF OFF 1 23 45 67 8ON OFF OFF OFF
CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIE (DAI) NEAX2000 IVS2 Remote PIM System Manual ND-70917 (E), Issue 1.0 Page 91 SW2 (DIP SW) 4Setting of control signal time slot NOTE 2, NOTE 3 OFF 5 OFF 6 OFF 7 OFF 8ON (Continued) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 45 67 8ON ON SWITCH NUMBER TIME SLOT NUMBER 45678 OFFONONONON TS1 ON OFF ON ON ON TS2 OFF OFF ON ON ON TS3 ON ON OFF ON ON TS4 OFF ON OFF ON ON TS5 ON OFF OFF ON ON TS6 OFF OFF OFF ON ON TS7 ON ON ON OFF ON TS8 OFF ON ON OFF ON TS9 ON OFF ON OFF ON TS10 OFF OFF ON OFF ON TS11 ON ON OFF OFF ON TS12 OFFONOFFOFFON TS13 ON OFF OFF OFF ON TS14 OFF OFF OFF OFF ON TS15 ON ON ON ON OFF TS16 OFFONONONOFF TS17 ON OFF ON ON OFF TS18 OFF OFF ON ON OFF TS19 ON ON OFF ON OFF TS20 OFF ON OFF ON OFF TS21 ON OFF OFF ON OFF TS22 OFF OFF OFF ON OFF TS23 ON ON ON OFF OFF TS24 OFF ON ON OFF OFF TS25 ON OFF ON OFF OFF TS26 OFF OFF ON OFF OFF TS27 OFF ON OFF OFF OFF TS29 ON OFF OFF OFF OFF TS30 OFF OFF OFF OFF OFF TS31 ON ON ON OFF
NEAX2000 IVS2 Remote PIM System ManualPage 92 ND-70917 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-DAIE (DAI) The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1:When the power is on, flip the MB switch to ON (UP position) before plugging/unplug- ging the circuit card. NOTE 2:Time Slot Number 0 and 28 (TS0/28) cannot be used for control signal. NOTE 3:This setting must be identical with the opposite DAID card. SW3 (DIP SW) 1 Always set to ON 2 Always set to ON 3 Always set to ON 4 Always set to OFF JPS (Jumper Pin) Balanced transmission: 120 ohms (for twisted-pair cable) LeftTA is grounded on the transmission line: 75 ohms (for coaxial cable) JPR (Jumper Pin) RightRA is grounded on the transmission line: 75 ohms (for coaxial cable) Balanced transmission: 120 ohms (for twisted-pair cable) E1Z (Jumper Pin) RightLine impedance: 75 ohms (for coaxial cable) Line impedance: 120 ohms (for twisted-pair cable) SRT (Jumper Pin) RightLine impedance: 75 ohms (for coaxial cable) Line impedance: 120 ohms (for twisted-pair cable) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK 1 23 4ON ON ON ON OFF Right Left Left Left