NEC Neax 2000 Ivs2 Oai System Manual

 NEAX2000 IVS2 OAI System ManualPage 54  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for ACF
DATA ASSIGNMENT FOR ACF
DESCRIPTION DATA
Specify the processor to check the ID 
Codes.(1)
(2)217
1  : AP (PN-AP01)
Specify whether SST is sent after dialing 
the access code for ID Code Class 
Change or not.(1)
(2)362
0  : No Tone
1  : Service Set Tone (SST)
Assign the number of digits for each ID 
code of Authorization Code/Forced 
Account Code/Remote Access to System 
(DISA).(1)...

CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for ACF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 55
DESCRIPTION DATA
Assign the return result waiting timer for 
the PBX sent facility.
(1)
(2)Y=3
00
000-127: 8-508 sec.  
(4-sec. increments)
If no data is set, the default setting is 
8 sec.
Assign the office number. 
(1)
(2)Y=5
00
Office No. (Max. 4 digits)
Assign the Number of ID code digits when 
AP stops during ACF operation.
(1)
(2)Y=B
00
0  : No ACF operation
1  : 1...

 NEAX2000 IVS2 OAI System ManualPage 56  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SSF
DATA ASSIGNMENT FOR SSF
DESCRIPTION DATA
Assign the Message Wait Indication (VM) 
for My Line only or My Line and sub-line 
on D
term.(1)
(2)140
0  : MW for My Line and sub-lines
1  : MW for My Line only
Whether Message Waiting/Message 
Reminder is reset (turning the MW Lamp 
off) by answering at the called station 
when the calling station calls again after 
setting this...

CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SMF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 57
DATA ASSIGNMENT FOR SMF
DESCRIPTION DATA
Assign the automatic setting of SMFR for 
D
term Sub line.(1)
(2)429
0  : Available
1  : Not available
Specify OAI SMFN STS (status) for Call 
Transfer from a station.(1)
(2)460
0  : SMFN STS=7
1  : SMFN STS=0
Specify whether OAI SMFN is sent when 
answering a held call.(1)
(2)461
0  : Sent
1  : Not sent
Specify whether ANI/Caller ID/CPN...

NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 59
CHAPTER 4
TROUBLESHOOTING
This chapter explains the troubleshooting information after installing
the OAI system. 

 NEAX2000 IVS2 OAI System ManualPage 60  ND-70922 (E), Issue 1.0
CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with RS-232C
TROUBLESHOOTING FOR OAI WITH RS-232C
This section explains the troubleshooting information for the OAI system with RS-232C. 
Table 4-1 shows the cause of trouble and the remedial action.
Table 4-1  Troubleshooting Information for OAI with RS-232C 
TROUBLE CAUSE ACTION
The PN-AP01 
does not set up. The AP data (07) of PN-AP01 
has not been assigned by CM05. Assign the AP data...

CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with RS-232C
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 61
The system 
cannot 
communicate 
with an external 
processor at all. In an external processor (RS-
232C) connection via MODEM, 
the RTS signal control of RS-232 
port has been effective (CMA6 
YY=11, 2nd Data=1). Assign 0 (RTS Signal ON) as the 
2nd data of CMA6 YY=11.
The OAI function 
key of D
term does 
not operate. The OAI function key has not 
been assigned by...

 NEAX2000 IVS2 OAI System ManualPage 62  ND-70922 (E), Issue 1.0
CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with TCP/IP-Ethernet
TROUBLESHOOTING FOR OAI WITH TCP/IP-ETHERNET
This section explains the troubleshooting information for the OAI system with TCP/IP-Ethernet.
Table 4-2 shows the cause of trouble and the remedial action. When a trouble occurs, do the
remedial action.
Troubleshooting Information for ETHER Card
The lamp indications on the PN-CC01 card on normal condition are as follows:...

CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with TCP/IP-Ethernet
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 63
Troubleshooting Information for PN-AP01 Card
Table 4-3  Troubleshooting Information for PN-AP01 Card
TROUBLE CAUSE ACTION
The PN-AP01 
does not set up. The AP data (07) of PN-AP01 
has not been assigned by CM05. Assign the AP data (07) by 
CM05, then initialize the PN-
AP01 (press SW1 of MP card).
 The AP data (07) of PN-AP01 
has been assigned to two slot...

 NEAX2000 IVS2 OAI System ManualPage 64  ND-70922 (E), Issue 1.0
CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with TCP/IP-Ethernet
Replacement Procedure for PN-AP01/PN-CC01 Card
When replacing the PN-AP01 card or the PN-CC01 card with power on, do the following
procedure.
(1) Procedure for PN-AP01 Card
(a) When unplugging:
 Set the MB switch on the PN-AP01 card to the UP position.
 Remove the BUS cable (48-TW-0.3 CONN CA).
 Unplug the PN-AP01 card from the card slot.
(b) When plugging in:
 Set...