NEC Neax 2000 Ivs2 Oai System Manual

 NEAX2000 IVS2 OAI System ManualPage 24  ND-70922 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
(3) Connect the 48-TW-0.3 CONN CA onto the “IP” connector on the PN-AP01 card, as shown 
in Figure 2-8.
(4) Connect the 10 BASE-T twisted pair cable (TIA/EIA category 3 or larger) onto the 10 BASE-
T HUB on the Ethernet.
Figure 2-8  Cabling 48-TW-0.3 CONN CA and 10 BASE-T Twisted Pair Cable
PN-CC01
PN-AP0148-TW-0.3 CONN CA (0.3 m/1 ft.) 10 BASE-T TWISTED PAIR CABLE (TIA/EIA CATEGORY 3 OR...

NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 25
CHAPTER 3
SYSTEM DATA 
PROGRAMMING
This chapter explains the programming procedure to provide the OAI
feature to the PBX. 

 NEAX2000 IVS2 OAI System ManualPage 26  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
How to Read This Chapter
HOW TO READ THIS CHAPTER
AP Initialization
When first programming the OAI system data, initialize the PN-AP01 card using the procedure
described in AP01 Initialization. 
Preparation before Programming
Before programming, confirm that the system is under the following conditions.
 The system is under On-Line mode. (“RUN” lamp is flashing on the MP card.)
 MB (Make Busy) switch of...

CHAPTER 3  SYSTEM DATA PROGRAMMING
List of Commands Related to OAI
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 27
LIST OF COMMANDS RELATED TO OAI
Table 3-1 shows the commands related to the OAI with each facility (MSF, TMF etc.).
Table 3-1  List of Commands Related to OAI 
ITEMRELATED COMMAND
COMMAND 
No.1ST DATA 2ND DATA MEANING
AP01
Initial-
ization 
DataCM05 Y=0 04-15 07 AP Number of PN-AP01
CMD6 Y=0 0000 CCC PN-AP01 Memory All Clear
OAI 
Com-
muni-
cation 
Data 
(TCP/
IP)CMD7...

 NEAX2000 IVS2 OAI System ManualPage 28  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
List of Commands Related to OAI
MSFCM10 000-763 EB000-
EB127Digital Announcement Trunk Card 
No.
CM12 YY=02 Station No. 00-15 Service Restriction Class
CM15 YY=59 00-15 1
CM20 Y=0-3 Access Code A084 MSF Access Code
CM20 Y=0-3 Access Code  A100-A102 Digital Announcement Trunk 
Access Code
CM41 Y=0 56 00-99 Message Replay Timer/Tone 
Sending Timer
CM49 YY=00 000-127 10 Announcement Service for OAI
CM90 YY=00...

CHAPTER 3  SYSTEM DATA PROGRAMMING
List of Commands Related to OAI
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 29
TMFCMD7 Y=0 F1032-
F1047192-255 TMF Operation Code
CMD7 Y=0 F1032-
F1047DCX (X=1-3) Digit Number of Digit Code
CMD7 Y=3 00 000-127 RR Timer
CMD7 Y=4 01 00-32 Maximum number of terminals to 
be in TMF simultaneously
CMD7 Y=6 Digit Code 192-255 Operation Code for TMF
CMD7 Y=7 F1032-
F104700/01
Chime from D
term when Receiving 
RR Signal
CMD7 Y=8 00-03 00/01
Chime from D...

 NEAX2000 IVS2 OAI System ManualPage 30  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
List of Commands Related to OAI
SCFCM42 10 01-06 Account Code Max. digit 
(SCF FID=1, 3, 4, 7)
CM49 YY=00 000-127 10/1602-1663 Announcement Service for OAI/
Message Group No. for Multi-
Connection Announcement 
Service for OAI
CMD7 Y=2 000-127 1000-1127 Digital Announcement Trunk Card 
No.
FLFCM08 216 1 AP (PN-AP01)
CM08 217 1 AP (PN-AP01) 
CM15 YY=31 00-15 0/1 Authorization Code/Forced 
Account Code
CM20...

CHAPTER 3  SYSTEM DATA PROGRAMMING
List of Commands Related to OAI
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 31
ACFCMD5 Y=3 ID code ABBCCDDEE Temporary Class Data
CMD7 Y=3 00 000-127 RR Timer
CMD7 Y=5 00 XXXX Office Number
CMD7 Y=B 00 0-3 Number of Digits for ID Codes 
when AP Stops
TCF None
NTF None
ADF None
SSF
(MW)CM08 140 0/1 Message Wait Indication (MW)
CM08 235 0 Message Waiting/Message 
Reminder reset
CM08 376 0/1 VMS via CCIS
CM08 443 0 VMS with MCI
CM08 444 0/1 Message...

 NEAX2000 IVS2 OAI System ManualPage 32  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
List of Commands Related to OAI
SMFCM08 429 0/1
D
term subline
CM08 460 0/1 SMFN STS (Status)
CM08 461 0/1 SMFN when answering a held call
CM08 462 0/1 ANI/Caller ID/CPN to OAI 
Terminal
CM08 464 0/1 TSAPI/SCF facility
CMD7 Y=A 02 0/1 SMFN/SSFN Delay Timer
MRF None
Health 
checkNone
Table 3-1  List of Commands Related to OAI (Continued)
ITEMRELATED COMMAND
COMMAND 
No.1ST DATA 2ND DATA MEANING 

CHAPTER 3  SYSTEM DATA PROGRAMMING
AP01 Initialization
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 33
AP01 INITIALIZATION
DESCRIPTION DATA
Assign an AP number to the AP01 card.
NOTE:The AP number must match the
SENSE switch settings on the
AP01 card.
(1)
(2)Y=0
AP Number (04-15)
07: AP01 card
Load the initial data into the AP01 card. 
(1)
(2)Y=0
0000
CCC
CMD6 START
END
CM05
INITIAL