NEC Neax 2000 Ivs2 Oai System Manual

NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 65
CHAPTER 5
CIRCUIT CARD 
INFORMATION
This chapter explains the mounting location, the meaning of lamp
indications, and the method of switch settings of each circuit card for
the OAI system. 

 NEAX2000 IVS2 OAI System ManualPage 66  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
How to Read This Chapter
HOW TO READ THIS CHAPTER
This chapter explains each circuit card used in this system about the following items.
Explanations are given in alphabetical order of the circuit card names within each circuit card
category (Control, Application Processor, and Line/Trunk).
(1) Locations of Lamps, Switches, and Connectors
The locations of lamps, switches, and connectors of each circuit...

CHAPTER 5  CIRCUIT CARD INFORMATION
Mounting Location of Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 67
MOUNTING LOCATION OF CIRCUIT CARD
This section explains the conditions for mounting circuit cards for the OAI.
Figure 5-1 shows circuit card mounting slots allocated in the PIM.
Figure 5-1  Mounting Location of Circuit Card
*1PN-CP15 (FP) is to be mounted in FP11 slot on PIM0.
*2PN-CP15 (FP) card is to be mounted in FP12 slot on PIM2/PIM4/PIM6.
*3PN-AP01 (AP01) card...

 NEAX2000 IVS2 OAI System ManualPage 68  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
LIST OF REQUIRED CIRCUIT CARD
Table 5-1 shows the required circuit cards to be explained in this section.
*MB = Make Busy
Table 5-1  List of Required Card
NAME
(FUNCTIONAL
NAME)LAMP
X:PROVIDED
–:NOT 
PROVIDEDSWITCH
X:PROVIDED
–:NOT 
PROVIDEDEXTRACTION/
INSERTION 
WITH POWER 
ON
X:ALLOWED
:ALLOWED 
AFTER MB*
–:NOT 
ALLOWEDREFERENCE
PAGE
PN-CP15 (FP) X XPage 69
PN-AP01 (AP01) X...

CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 69
PN-CP15 (FP)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while the circuit card is operating normally.
SENSE
RUN
MB
SW1 

 NEAX2000 IVS2 OAI System ManualPage 70  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch...

CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 71
PN-AP01 (AP01)
Locations of Lamps, Switches and Connectors
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
L0-L3 L3 Green Indication of CTS signal status on RS-232C port.
L2 Indication of DCD signal status on RS-232C port.
L1 Indication of TXD signal status on RS-232C port.
L0 Indication of RXD signal status...

 NEAX2000 IVS2 OAI System ManualPage 72  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-15) to 
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW1
(Piano Key SW)
1For normal operation
OFF Not used
2For normal operation
OFF Not used
3For normal operation
OFF Not used
4For normal...

CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 73
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON (UP...

 NEAX2000 IVS2 OAI System ManualPage 74  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
PN-CC01 (ETHER)
Location of Lamps, Switches and Connectors
RUN
MB
LINK 
XMT 
RCV 
RVP 
ERR
IP 10BASE-T
SW1SW2