NEC Neax 2000 Ivs2 Oai System Manual

							NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 65
CHAPTER 5
CIRCUIT CARD 
INFORMATION
This chapter explains the mounting location, the meaning of lamp
indications, and the method of switch settings of each circuit card for
the OAI system. 
						

							 NEAX2000 IVS2 OAI System ManualPage 66  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
How to Read This Chapter
HOW TO READ THIS CHAPTER
This chapter explains each circuit card used in this system about the following items.
Explanations are given in alphabetical order of the circuit card names within each circuit card
category (Control, Application Processor, and Line/Trunk).
(1) Locations of Lamps, Switches, and Connectors
The locations of lamps, switches, and connectors of each circuit card are shown by a face 
layout.
(2) Lamp Indications
The name, color, and functions of each indicator lamp equipped on each circuit card are 
described in a table.
(3) Switch Settings
The name, settings, and functions of each switch equipped on each circuit card are 
described in a table.
Each switch setting table has a “CHECK” column. Make necessary entries in the CHECK column
during and/or after the system installation and maintenance, and use each table as a reference
for subsequent system maintenance and operations. 
						

							CHAPTER 5  CIRCUIT CARD INFORMATION
Mounting Location of Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 67
MOUNTING LOCATION OF CIRCUIT CARD
This section explains the conditions for mounting circuit cards for the OAI.
Figure 5-1 shows circuit card mounting slots allocated in the PIM.
Figure 5-1  Mounting Location of Circuit Card
*1PN-CP15 (FP) is to be mounted in FP11 slot on PIM0.
*2PN-CP15 (FP) card is to be mounted in FP12 slot on PIM2/PIM4/PIM6.
*3PN-AP01 (AP01) card and PN-CC01 (ETHER) card are to be mounted in AP00-AP10 slots on PIM0, and on
the AP00-AP11 slots on PIM1-7.
LT 0 9 / A P 0 9LT 0 8 / A P 0 8LT 0 7 / A P 0 7
LTC1LTC0LTC2
BWB
PIM
0~7
FRONTAC/DC
PWR
LT 1 0 / A P 1 0LT00/AP00LT 0 1 / A P 0 1LT 0 2 / A P 0 2LT 0 3 / A P 0 3LT 0 4 / A P 0 4LT 0 5 / A P 0 5LT 0 6 / A P 0 6LT 11 / A P 11 / F P 11MP12/FP12
LTC3
DC/DC
PWR
PFTVM
*1*2
*3 
						

							 NEAX2000 IVS2 OAI System ManualPage 68  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
LIST OF REQUIRED CIRCUIT CARD
Table 5-1 shows the required circuit cards to be explained in this section.
*MB = Make Busy
Table 5-1  List of Required Card
NAME
(FUNCTIONAL
NAME)LAMP
X:PROVIDED
–:NOT 
PROVIDEDSWITCH
X:PROVIDED
–:NOT 
PROVIDEDEXTRACTION/
INSERTION 
WITH POWER 
ON
X:ALLOWED
:ALLOWED 
AFTER MB*
–:NOT 
ALLOWEDREFERENCE
PAGE
PN-CP15 (FP) X XPage 69
PN-AP01 (AP01) X XPage 71
PN-CC01
(ETHER)XX XPage 74 
						

							CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 69
PN-CP15 (FP)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while the circuit card is operating normally.
SENSE
RUN
MB
SW1 
						

							 NEAX2000 IVS2 OAI System ManualPage 70  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON (UP position) before plugging/
unplugging the circuit card. 
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE 
(Rotary SW)
NOTE 10-3For setting FP No.
0 For mounting this card in PIM0
1 For mounting this card in PIM2
2 For mounting this card in PIM4
3 For mounting this card in PIM6
4-F Not used
MB (Toggle SW)
NOTE 2UPFor make-busy
For normal operation
SW1
(Piano Key SW)1 - 3Not used
4For normal operation
OFFNot used
0
1
2
3
ON
DOWN
4 
3 
2 
1 OFF
ON
OFF
ON 
						

							CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 71
PN-AP01 (AP01)
Locations of Lamps, Switches and Connectors
Lamp Indications
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
L0-L3 L3 Green Indication of CTS signal status on RS-232C port.
L2 Indication of DCD signal status on RS-232C port.
L1 Indication of TXD signal status on RS-232C port.
L0 Indication of RXD signal status on RS-232C port.
RS0
SENSE
RUN
MB
SW1
L3 
L2 
L1 
L0
SW0
IP
J19 
						

							 NEAX2000 IVS2 OAI System ManualPage 72  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-15) to 
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW1
(Piano Key SW)
1For normal operation
OFF Not used
2For normal operation
OFF Not used
3For normal operation
OFF Not used
4For normal operation
OFF Not used
(Continued)
F
4AP No.04 05 06 07 08 09 10 11 12 13 14 15
SW No.456789ABCDEF
ON
DOWN
4 
3 
2 
1 OFF
ON
ON
ON
ON
ON 
						

							CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 73
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON (UP position) before plugging/
unplugging the circuit card. SW0 (Dip SW)
1ON Receives RT clock
Uses internal clock
2ON Receives ST2 clock
Uses internal clock
3ON Sends ST1 clock
Not send ST1 clock
4 Not used 
J19
For normal operation
(Memory backup ON)
LEFTNot used 
(Memory backup OFF)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
4ONOFF
OFF
OFF
OFF
Front (Jumper pin)
RIGHT 
						

							 NEAX2000 IVS2 OAI System ManualPage 74  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
PN-CC01 (ETHER)
Location of Lamps, Switches and Connectors
RUN
MB
LINK 
XMT 
RCV 
RVP 
ERR
IP 10BASE-T
SW1SW2