NEC Neax 2000 Ivs2 Oai System Manual

							 NEAX2000 IVS2 OAI System ManualPage 54  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for ACF
DATA ASSIGNMENT FOR ACF
DESCRIPTION DATA
Specify the processor to check the ID 
Codes.(1)
(2)217
1  : AP (PN-AP01)
Specify whether SST is sent after dialing 
the access code for ID Code Class 
Change or not.(1)
(2)362
0  : No Tone
1  : Service Set Tone (SST)
Assign the number of digits for each ID 
code of Authorization Code/Forced 
Account Code/Remote Access to System 
(DISA).(1)
(2)11: Authorization Code
12: Forced Account Code
13: Remote Access to System (DISA)
01-10: Number of digits
Assign the Access code for ID Code 
Class Change.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
A086: Authorization Code
A087: Forced Account Code
Assign the Temporary Class data to the 
ID codes.
NOTE:This data is to use PBX internal 
class change data when ACF is 
in operation and the AP stopped.
The number of digits is set 
through CMD7 Y=B.
(1)
(2)Y=3 
ID code
A BB CC DD EE
A: Type of Temporary Service Class
0: Unrestricted
1: Fully-Restricted
2: Temporary Service Class
9: Delete of the ID Code
BB: 01-08: Trunk Restriction Class
CC: 00-15: Service Feature Class-A
DD: 00-15: Service Feature Class-B
EE: 00-15: Service Feature Class-C
CM20 START
CM08
A
CM42
CMD5 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for ACF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 55
DESCRIPTION DATA
Assign the return result waiting timer for 
the PBX sent facility.
(1)
(2)Y=3
00
000-127: 8-508 sec.  
(4-sec. increments)
If no data is set, the default setting is 
8 sec.
Assign the office number. 
(1)
(2)Y=5
00
Office No. (Max. 4 digits)
Assign the Number of ID code digits when 
AP stops during ACF operation.
(1)
(2)Y=B
00
0  : No ACF operation
1  : 1 digit
2  : 2 digits
3  : 3 digits
END
CMD7
A 
						

							 NEAX2000 IVS2 OAI System ManualPage 56  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SSF
DATA ASSIGNMENT FOR SSF
DESCRIPTION DATA
Assign the Message Wait Indication (VM) 
for My Line only or My Line and sub-line 
on D
term.(1)
(2)140
0  : MW for My Line and sub-lines
1  : MW for My Line only
Whether Message Waiting/Message 
Reminder is reset (turning the MW Lamp 
off) by answering at the called station 
when the calling station calls again after 
setting this feature.(1)
(2)235
0: Available
When a forwarded call is terminated to the 
VMS via CCIS, Whether Message Waiting 
from the VMS is provided for the called 
station.(1)
(2)376
0  : To provide
1  : Not provided
Assign the Type of Voice Mail System.  (1)
(2)443
0: VMS with MCI
Message Waiting lamp control from VMS 
with MCI to all stations.
NOTE:MW lamp control is only 
available to the stations in the 
opposite PBX connected with 
CCIS via MCI.
Station dialing MW access codes 
are not allowed over CCIS.(1)
(2)444
0: Available
Assign the Message Waiting/Message 
Reminder.
(1)
(2)YY=03
X-XXXX: Station No.
0: To provide (For the station with MW
lamp)
START
CM08
END
CM13 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SMF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 57
DATA ASSIGNMENT FOR SMF
DESCRIPTION DATA
Assign the automatic setting of SMFR for 
D
term Sub line.(1)
(2)429
0  : Available
1  : Not available
Specify OAI SMFN STS (status) for Call 
Transfer from a station.(1)
(2)460
0  : SMFN STS=7
1  : SMFN STS=0
Specify whether OAI SMFN is sent when 
answering a held call.(1)
(2)461
0  : Sent
1  : Not sent
Specify whether ANI/Caller ID/CPN is 
sent to OAI terminal.(1)
(2)462
0  : Available
1  : Not available
Assign the OAI-TSAPI/SCF facility. (1)
(2)464
0  : Same as IMX system
(recommended setting)
1  : SMFN Off-Hook indication sent
Assign the SMFN/SSFN delay timer 
(1)
(2)Y=A
02
0  : Immediate start
1  : 512 msec. delay
START
CM08
END
CMD7 
						

							NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 59
CHAPTER 4
TROUBLESHOOTING
This chapter explains the troubleshooting information after installing
the OAI system. 
						

							 NEAX2000 IVS2 OAI System ManualPage 60  ND-70922 (E), Issue 1.0
CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with RS-232C
TROUBLESHOOTING FOR OAI WITH RS-232C
This section explains the troubleshooting information for the OAI system with RS-232C. 
Table 4-1 shows the cause of trouble and the remedial action.
Table 4-1  Troubleshooting Information for OAI with RS-232C 
TROUBLE CAUSE ACTION
The PN-AP01 
does not set up. The AP data (07) of PN-AP01 
has not been assigned by CM05. Assign the AP data (07) by 
CM05, then initialize the PN-
AP01 (press SW1 of MP card).
 The AP data (07) of PN-AP01 
has been assigned to two slot 
numbers. Delete one data of the two, then 
initialize the PN-AP01 (press 
SW1 of MP card).
 The unused data have been 
assigned by CMA6. Confirm the programming 
procedure of Chapter 3, then 
assign the correct data.
The system 
cannot 
communicate 
with an external 
processor at all. The cables between the system 
and an external processor have 
not been connected properly. Connect the cables properly.
 The attribute data for RS-232C 
port of PN-AP01 have not been 
assigned by CMA6. When providing OAI with RS-
232C, assign the attribute data in 
accordance with the external 
processor attribution.
 The attribute data assigned by 
CMA6 have not coincided with 
the external processor attribution. When providing the OAI with 
RS-232C, assign the attribute 
data in accordance with the 
external terminal attribution.
 The PN-AP01 has not been 
initialized after the programming 
of CMA6. Initialize the PN-AP01 (Move the 
MB switch on the PN-AP01 up 
and down).
 The switches of MODEM have 
not been set properly. Set the switches properly. 
						

							CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with RS-232C
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 61
The system 
cannot 
communicate 
with an external 
processor at all. In an external processor (RS-
232C) connection via MODEM, 
the RTS signal control of RS-232 
port has been effective (CMA6 
YY=11, 2nd Data=1). Assign 0 (RTS Signal ON) as the 
2nd data of CMA6 YY=11.
The OAI function 
key of D
term does 
not operate. The OAI function key has not 
been assigned by CM90. Assign the OAI function key to 
Dterm.
 The operation code for MSF/TMF 
has not been assigned by CMD7 
Y=0. Assign the operation code.
 The operation code for MSF/TMF 
has not been accepted by the 
external processor. Check the application program of 
the external processor, then 
assign correct operation code.
Table 4-1  Troubleshooting Information for OAI with RS-232C (Continued)
TROUBLE CAUSE ACTION 
						

							 NEAX2000 IVS2 OAI System ManualPage 62  ND-70922 (E), Issue 1.0
CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with TCP/IP-Ethernet
TROUBLESHOOTING FOR OAI WITH TCP/IP-ETHERNET
This section explains the troubleshooting information for the OAI system with TCP/IP-Ethernet.
Table 4-2 shows the cause of trouble and the remedial action. When a trouble occurs, do the
remedial action.
Troubleshooting Information for ETHER Card
The lamp indications on the PN-CC01 card on normal condition are as follows:
NOTE:Confirm connection of a cable if a lamp disappears.
Table 4-2  Troubleshooting Information for ETHER Card
TROUBLE CAUSE ACTION
The system 
cannot 
communicate 
with an external 
processor at all. The cables between the system 
and an external processor have 
not been connected properly. Connect the cable properly.
 The IP Address overlaps with 
another. Confirm the data set by CMD7 
Y=9, and assign the correct data.
 The MAC Address overlaps with 
another. Confirm the switch setting on the 
PN-CC01 card, and set correctly.
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 60 IPM while this card is operating normally.
LINK Green Lights when link is established. NOTE
XMT Green Lights when transmitting data.
RCV Green Lights when receiving data.
RVP Green Lights when receiving data with own IP Address.
ERR Not used 
						

							CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with TCP/IP-Ethernet
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 63
Troubleshooting Information for PN-AP01 Card
Table 4-3  Troubleshooting Information for PN-AP01 Card
TROUBLE CAUSE ACTION
The PN-AP01 
does not set up. The AP data (07) of PN-AP01 
has not been assigned by CM05. Assign the AP data (07) by 
CM05, then initialize the PN-
AP01 (press SW1 of MP card).
 The AP data (07) of PN-AP01 
has been assigned to two slot 
numbers. Delete one data of the two, then 
initialize the PN-AP01 (press 
SW1 of MP card).
 The unused data have been 
assigned by CMA6. Confirm the programming 
procedure of CHAPTER 3, then 
assign the correct data. 
						

							 NEAX2000 IVS2 OAI System ManualPage 64  ND-70922 (E), Issue 1.0
CHAPTER 4  TROUBLESHOOTING
Troubleshooting for OAI with TCP/IP-Ethernet
Replacement Procedure for PN-AP01/PN-CC01 Card
When replacing the PN-AP01 card or the PN-CC01 card with power on, do the following
procedure.
(1) Procedure for PN-AP01 Card
(a) When unplugging:
 Set the MB switch on the PN-AP01 card to the UP position.
 Remove the BUS cable (48-TW-0.3 CONN CA).
 Unplug the PN-AP01 card from the card slot.
(b) When plugging in:
 Set the MB switch on the PN-AP01 card to the UP position.
 Plug in the PN-AP01 card to the card slot.
 Connect the BUS cable with the PN-AP01 card.
 Set the MB switch on the PN-AP01 card to the DOWN position.
(2) Procedure for PN-CC01 Card
(a) When unplugging:
 Remove the transceiver cable/10 BASE-T cable.
 Remove the BUS cable.
 Set the MB switch on the PN-CC01 to the UP position.
 Unplug the PN-CC01 card from the card slot.
(b) When plugging in:
 Set the MB switch on the PN-CC01 to the UP position.
 Plug in the PN-CC01 card to the card slot.
 Connect the BUS cable with the PN-CC01 card.
 Connect the 10 BASE-T cable with the PN-CC01 card.
 Set the MB switch on the PN-CC01 to the DOWN position.