NEC Neax 2000 Ivs2 Oai System Manual
Have a look at the manual NEC Neax 2000 Ivs2 Oai System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NEAX2000 IVS2 OAI System ManualPage 14 ND-70922 (E), Issue 1.0 CHAPTER 2 INSTALLATION Precautions Caution You must hold the edge of a circuit card when plugging or unplugging the circuit card. If you touch another area, you may be exposed to hazardous voltages. CARD FRONT NEVER TOUCH THE COMPONENTS OR SOLDERED SURFACE WITH BARE HANDS. PBX
CHAPTER 2 INSTALLATION Required Equipment NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 15 REQUIRED EQUIPMENT Table 2-1 and Table 2-2 show the required equipment when the OAI is provided through an external processor with RS-232C interface, or through the Ethernet with TCP/IP. Required Equipment for OAI with RS-232C Interface Table 2-1 Required Equipment for OAI with RS-232C Interface EQUIPMENT DESCRIPTION QTY REMARKS PN-AP01 OAI Interface Card 1 RS NORM-4 CA-A /RS NORM-4S CA-AConnecting Cable between PN-AP01 and MODEM (Required if 15 m/49 ft. or more)1 Cable length: 4 m/13 ft. RS RVS-4 CA-A /RS RVS-4S CA-A /RS RVS-4 CA-C /RS RVS-4S CA-CConnecting Cable between PN-AP01 and External Processor1 Cable length: 4 m/13 ft. or RS RVS-15 CA-A /RS RVS-15S CA-A1 Cable length: 15 m/49 ft. RS-232C Cable Connecting Cable between External Processor and MODEM1 Required if 15 m/49 ft. or more is needed (Should be provided by customer) External Processor with RS-232C Interface1 (Should be provided by customer) MODEM Refer to MODEM Specification. Page 92 Required if 15 m/49 ft. or more is needed (Should be provided by customer)
NEAX2000 IVS2 OAI System ManualPage 16 ND-70922 (E), Issue 1.0 CHAPTER 2 INSTALLATION Required Equipment Required Equipment for OAI with TCP/IP-Ethernet Table 2-2 Required Equipment for OAI with TCP/IP-Ethernet EQUIPMENT DESCRIPTION QTY REMARKS PN-AP01 OAI Interface Card 1 PN-CC01 Ethernet Control Card 1 48-TW-0.3 CONN CA BUS Cable between PN- AP01 and PN-CC011 Cable length: 0.3 m/1 ft. 10 BASE-T twisted pair cable (TIA/EIA category 3 or larger)10 BASE-T Cable between PN-CC01 and Ethernet1 Cable length: Max. 100 m/328 ft. (Should be provided by customer) NOTE
CHAPTER 2 INSTALLATION Installation Procedure NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 17 INSTALLATION PROCEDURE Installation Procedure for OAI with RS-232C Install the OAI system with RS-232C interface according to the following procedure. Figure 2-2 Installation Procedure for OAI with RS-232C Interface Installation Procedure for OAI with TCP/IP-Ethernet Install the OAI system with TCP/IP-Ethernet according to the following procedure. Figure 2-3 Installation Procedure for OAI with TCP/IP-Ethernet Mounting PN-CP15 Card Mounting PN-AP01 Card Cabling Between PN-AP01 Card and External Processor END START Page 18 Page 20 Page 21 END START Cabling BUS Cable and 10 BASE-T Cable Mounting PN-CC01 Card Mounting PN-AP01 Card Mounting PN-CP15 Card Page 18 Page 19 Page 20 Page 23
NEAX2000 IVS2 OAI System ManualPage 18 ND-70922 (E), Issue 1.0 CHAPTER 2 INSTALLATION Installation Procedure Mounting PN-AP01 Card (1) Confirm the correct switch settings. See CHAPTER 5.Page 65 Before mounting the card, set the MB switch to UP position. (2) Mount the PN-AP01 card in one of the following AP slots. PIM 0 : AP00-AP10 slot PIM 1-7: AP00-AP11 slot After mounting the card, set the MB switch to DOWN position.Contents Static Sensitive: Precautions Required HandlingATTENTION
CHAPTER 2 INSTALLATION Installation Procedure NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 19 Mounting PN-CC01 Card (1) Confirm the correct switch settings. See CHAPTER 5. Page 65 (2) Mount the PN-CC01 card in one of the following AP slots. PIM 0 : AP00-AP10 slot PIM 1-7: AP00-AP11 slotContents Static Sensitive: Precautions Required HandlingATTENTION
NEAX2000 IVS2 OAI System ManualPage 20 ND-70922 (E), Issue 1.0 CHAPTER 2 INSTALLATION Installation Procedure Mounting PN-CP15 Card (1) Confirm the correct switch settings. See CHAPTER 5. Page 65 Before mounting the card, set the MB switch to UP position. (2) Mount one PN-CP15 card in the each FP slot of PIM0, PIM2, PIM4 and PIM6, according to the system configuration. After mounting the card, set the MB switch to DOWN position.Contents Static Sensitive: Precautions Required HandlingATTENTION
CHAPTER 2 INSTALLATION Installation Procedure NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 21 Cabling between PN-AP01 Card and External Processor (1) Connect the RS RVS cable or RS NORM cable onto the “RS0” connector on the PN-AP01 card, as shown in Figure 2-4. Figure 2-4 Cable Running of RS RVS Cable/RS NORM Cable PN-AP01 RS RVS-4(S) CA-A/RS RVS-4(S) CA-C TO EXTERNAL IP PROCESSOR/MODEM RS RVS-15(S) CA-A/RS NORM-4 CA-A/RS NORM-4S CA-A RS0
NEAX2000 IVS2 OAI System ManualPage 22 ND-70922 (E), Issue 1.0 CHAPTER 2 INSTALLATION Installation Procedure (2) Connect the RS RVS cable or RS NORM cable, as shown in Figure 2-5 and Figure 2-6. When connecting an External Processor directly: Connect the External Processor to the PN-AP01 using an RS RVS-4(S) CA-A/RS RVS-4(S) CA-C/RS RVS-15(S) CA-A cable, as shown in Figure 2-5. Figure 2-5 Direct Connection When connecting an External Processor using MODEMs: Connect the External Processor through the MODEMs, as shown in Figure 2-6. In this case, the RS NORM-4 CA-A/RS NORM-4S CA-A should be used for DCE-DCE connection. When the cable length between the External Processor and PBX is more than 15 m/49 ft., MODEMs are required. Figure 2-6 MODEM Connection PBX (PIM0-PIM7) PN- AP01RS0 RS RVS-4(S) CA-A/RS RVS-4(S) CA-C (4 m/13.1 ft.) External Processor (RS-232C) RS RVS-15(S) CA-A (15 m/49 ft.) External Processor (RS-232C) MODEM MODEM RS NORM-4 CA-A/RS NORM-4S CA-A (4 m /13 ft.) PN- AP01RS0 PBX (PIM0-PIM7) 2P
CHAPTER 2 INSTALLATION Installation Procedure NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 23 Cabling BUS Cable and 10 BASE-T Cable (1) Connect the 48-TW-0.3 CONN CA (BUS cable) onto the “IP” connector on the PN-CC01 card, as shown in Figure 2-7. (2) Connect the 10 BASE-T twisted pair cable (TIA/EIA Category 3 or larger) onto the “10 BASE-T” connector on the PN-CC01 card, as shown in Figure 2-7. Figure 2-7 Cable Connections on PN-CC01 Card TO PN-AP01 48-TW-0.3 CONN CA IP PN-CC01 10 BASE-TTO 10 BASE-T HUB 10 BASE-T TWISTED PAIR CABLE(TIA/EIA CATEGORY 3 OR LARGER)