NEC Neax 2000 Ivs2 Oai System Manual

							 NEAX2000 IVS2 OAI System ManualPage 34  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
OAI Communication Data Assignment (TCP/IP)
OAI COMMUNICATION DATA ASSIGNMENT (TCP/IP)
NOTE 1:The IP Address must be assigned to the 1st data 00-03 as follows.
IP Address: AAA.BBB.CCC.DDD [AAA-DDD: 2nd Data (2)]
NOTE 2:When setting the 2nd Data as shown in Table 3-2 IP Address Assignment Patterns
(PN-CC01 Card) (See Page 35), note that the setting data is different from the data
actually assigned.
IP Address: AAA.BBB.CCC.DDD
DESCRIPTION DATA
Assign the IP Address of TCP/IP-Ethernet.
NOTE 1, NOTE 2

(1)
(2)Y=9
00-03: Division No. of IP Address
0-255: Address Data (1-3 digits)
1st Data (1) 00: AAA
01: BBB
02: CCC
03: DDD
START
CMD7
END
AP01 INITIAL 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
OAI Communication Data Assignment (TCP/IP)
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 35
Table 3-2  IP Address Assignment Patterns (PN-CC01 Card)
PATTERNINPUT DATA (2ND DATA)
ASSIGNED DATA
AAA BBB CCC DDD
When no data 
or all 0 is input
No data No data No data No data4C.A4.XX.XX (HEX)
4C.A4: Fixed
XX.XX: According to the 
switch setting of 
SW1 (D15-D8) 
and SW2 (D7-D0)
(The IP Address is the 
same as lower 32 bits of 
MAC Address.)
0000
When the data 
only for 
Address AAA is 
input
0≤AAA
≤127000A.A4.XX.XX (HEX)
A.A4: Fixed
XX.XX: According to the 
switch setting of 
SW1 (D15-D8) 
and SW2 (D7-D0)
(The lower 24 bits of IP 
Address is the same as the 
lower 24 bits of MAC 
Address.)
When the data 
only for 
Address AAA 
and BBB is 
input 128≤AA
A
≤1910≤BBB
≤2550A.B.XX.XX (HEX)
A.B: Fixed
XX.XX: According to the 
switch setting of 
SW1 (D15-D8) 
and SW2 (D7-D0)
(The lower 16 bits of IP 
Address is the same as the 
lower 16 bits of MAC 
Address.) 
						

							 NEAX2000 IVS2 OAI System ManualPage 36  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
OAI Communication Data Assignment (RS-232C)
OAI COMMUNICATION DATA ASSIGNMENT (RS-232C)
DESCRIPTION DATA
Assign the attribute data for RS-232C port 
of the PN-AP01.
(1)
(2)YY=04 Data Transmission Speed of 
RS-232C port
3
0: 150 bps
1: 300 bps
2: 600 bps
3: 1200 bps
4: 2400 bps
5: 4800 bps
6: 9600 bps

(1)
(2)YY=05 Parity Check
3
1  : Ineffective

(1)
(2)YY=06 Synchronous/Asynchronous
3
7  : Asynchronous

(1)
(2)YY=07 Duplex/Half-duplex
3
1  : Duplex
START
CMA6
A
AP01 INITIAL 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
OAI Communication Data Assignment (RS-232C)
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 37
DESCRIPTION DATA

(1)
(2)YY=08 Stop Bit
3
1  : 1-Stop Bit

(1)
(2)YY=09 Type of Code
3
06: JIS (8-bit)

(1)
(2)YY=10 Flow Control by DCD Signal
3
0  : Ineffective
1 :Effective

(1)
(2)YY=11 RTS Signal Control
3
0  : Ineffective (RTS Signal ON)
1 :Effective
NOTE:When connecting an external
processor with RS-232C in-
terface via MODEM, assign 0
(RTS Signal ON) as the 2nd
data.

(1)
(2)YY=12 Designation of Signal for 
Detecting Line Disconnection
3
0  : DCD (with MODEM)
1  : DSR (without MODEM)

(1)
(2)YY=20 Designation of Facility
3
2: OAI

(1)
(2)YY=21 Priority
3
0: 1st Priority

(1)
(2)YY=24 Kind of Procedure
3
1: Free Wheel
END
CMA6
A
AP01 INITIAL 
						

							 NEAX2000 IVS2 OAI System ManualPage 38  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for MSF
DATA ASSIGNMENT FOR MSF
To start up MSF from Dterm by using an OAI function key:
DESCRIPTION DATA
Assign the OAI function key for starting up 
MSF to a D
term.
(1)
(2)YY=00
My Line No. +   + Key No.
F1032-F1047: OAI Function Key 
No. 0-15
When pressing the OAI function key to 
start up MSF, assign the operation code 
to the OAI function key assigned by 
CM90.
(1)
(2)Y=0
F1032-F1047: OAI Function Key
No. 0-15
128-191: Operation Code for MSF
When dialing a digit code (1-3 digits) after 
pressing OAI function key to start up 
MSF, assign the digit number of digit 
code, then assign the operation code to 
the digit code.
(1)
(2)Y=0
F1032-F1047: OAI Function Key
No. 0-15
DCX (X=1-3) : Digit Number of Digit
Code

(1)
(2)Y=6
X-XXX: Digit Code (X=0-9, #)
128-191: Operation Code for MSF
Assign the waiting timer for receiving an 
answer signal (RR signal) after starting up 
MSF, if required.
(1)
(2)Y=3
00
000-127: 8-508 sec. 
(4-sec. increments)
If no data is set, the default setting is 8 sec.
Specify a chime from D
term when 
receiving RR signal of MSF.
(1)
(2)Y=7
F1032-F1047: OAI Function Key 
No. 0-15
00  : Not sent
01  : To send
CMD7 START
CM90
END
, 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for MSF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 39
To start up MSF from PB Telephone/Dterm by using an access code:
DESCRIPTION DATA
Assign the Service Restriction Class for 
starting up MSF to the required stations.
NOTE:After starting up the MSF from a 
PB telephone or Dterm, the PB re-
ceiver is busy during MSF mode. 
Therefore, you must make sure 
that a call origination is not avail-
able if all PB receivers are used. 
To prevent the “all busy,” we rec-
ommend using the OAI function 
key on D
term, as the PB receiver 
is not used for the Dterm.
(1)
(2)YY=02 
X-XXXX: Station No. 
XX ZZ
ZZ: 00-15  : Service Restriction Class
 B

(1)
(2)YY=59 
00-15: Service Restriction Class B
assigned by CM12 Y=02
1 : Allow
Assign the access code for starting up 
MSF.
(1)
(2)Y=0-3 Number Plan Group 0-3
X-XXXX: Access Code for MSF
A084
Assign the operation code to the access 
code assigned by CM20>A084.
NOTE 1:The operation code means a
number to designate each OAI
application.
NOTE 2:The maximum number of
operation code is 16.
(1)
(2)Y=1
X-XXXX: Access Code assigned by
CM20>A084
128-191: Operation Code for MSF
Assign the waiting timer for receiving an 
answer signal after starting up MSF, if 
required.
(1)
(2)Y=3
00
000-127: 8-508 sec.
(4-sec. increments)
If no data is set, the default setting is 000 
(8-sec.).
Assign the number of the terminal (PB 
telephone) to be in the terminal mode 
simultaneously.•
(1)
(2)Y=4
00
00  -32 : Number of Terminal
CM20 START
CM12
A
CM15
CMD7 
						

							 NEAX2000 IVS2 OAI System ManualPage 40  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for MSF
DESCRIPTION DATA
When sending a message through the 
Digital Announcement Trunk (PN-2DATA) 
to PB telephone/D
term user by using TCF-
D facility:
When sending a tone to PB telephone/
D
term user by using TCF-D facility:
When not sending a message or tone:
A
CMD7
C
B
END 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for MSF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 41
DESCRIPTION DATA
Assign a Digital Announcement Trunk 
card number to the required LEN.
NOTE 1:The Digital Announcement 
Trunk card number must be 
assigned to the first LEN (Level 
0), the third LEN (Level 2), the 
fifth LEN (Level 4) and the 
seven LEN (Level 6) of each LT 
slot.
NOTE 2:EB000 and EB001 are 
dedicated to built-in Digital 
Announcement Trunk of the MP 
card.(1)
(2)LEN: 000-763
EB002-EB127: Digital Announcement
Trunk Card No.
For PIM0/1: EB002-EB031
For PIM2/3: EB032-EB063
For PIM4/5: EB064-EB095
For PIM6/7: EB096-EB127
NOTE 2
Assign the function of the Digital 
Announcement Trunk card.
(1)
(2)YY=00
000-001: Built-in DAT on MP card
002-127: Digital Announcement Trunk
Card No. assigned by CM10
(EB002-EB127)
10: Announcement Service in the OAI
Terminal mode
To record, replay or delete a message, 
assign the respective Digital 
Announcement Trunk access code.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
A100: Record
A101: Replay
A102: Delete
Specify the message replay timer in the 
OAI terminal mode, if required.
(1)
(2)Y=0
56
01-99: 0-396 sec. (4 sec. increments)
If no data is set, the default setting is 20-24 
sec.
Assign the Digital Announcement Trunk 
card number.
(1)
(2)Y=2 
000-127: Message No. 
1 XXX
XXX: 000-127: Digital Announcement
Trunk Card No.
assigned by CM10
CM10
B
END
CMD7
CM41
CM20
CM49 
						

							 NEAX2000 IVS2 OAI System ManualPage 42  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for MSF
DESCRIPTION DATA
Specify the tone sending timer in the OAI 
terminal mode, if required.
(1)
(2)Y=0
56
01-99: 0-396 sec. (4 sec. increments)
If no data is set, the default setting is 20-24 
sec.CM41
C
END 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for TMF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 43
DATA ASSIGNMENT FOR TMF
DESCRIPTION DATA
Assign the OAI function key for starting up 
TMF to a D
term.
(1)
(2)YY=00
My Line No. +   + Key No.
F1032-F1047: OAI Function Key 
No. 0-15
When you start up the TMF by pressing 
the OAI function key, assign the operation 
code to the OAI function key assigned by 
CM90.
(1)
(2)Y=0
F1032-F1047: OAI Function Key
No. 0-15
192-255: Operation Code for TMF
When you start up the TMF by dialing a 
digit code (1-3 digits) after pressing the 
OAI function key, assign the digit number 
of the digit code, then assign the 
operation code to the digit code.
(1)
(2)Y=0
F1032-F1047: OAI Function Key
No. 0-15
DCX (X=1-3): Digit Number of Digit
Code

(1)
(2)Y=6
X-XXX: Digit Code (X=0-9, #)
192-255: Operation Code for TMF
Assign the waiting timer for receiving an 
answer signal after starting up the TMF, if 
required.
(1)
(2)Y=3
00
000-127: 8-508 sec. in 4-sec.
increments
If no data is set, the default setting is 
8 seconds.
Assign the maximum number of terminals 
to be in TMF simultaneously.
(1)
(2)Y=4
01
00 : 32 terminals
01-32 : Number of Terminal
CMD7 START
CM90
A,