NEC Neax 2000 Ivs2 Oai System Manual

							CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 75
Lamp Indications
Switch Settings
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 60 IPM while this card is operating normally.
LINK Green Remains lit when link is established.
XMT Green Remains lit when it is transmitting the data.
RCV Green Remains lit when it is receiving the data.
RVP Green Remains lit only when it is receiving the data with its own IP 
address.
ERR – Not used
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTIONCHECK
MB (Toggle SW)
NOTE 1UP For make-busy
For normal operation
(Continued)
ON
DOWN 
						

							 NEAX2000 IVS2 OAI System ManualPage 76  ND-70922 (E), Issue 1.0
CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
SW1 (DIP SW)
NOTE 21 (D15) ON
2 (D14) ON
3 (D13) ON
4 (D12) OFF
5 (D11)ON
OFF
6 (D10)ON
OFF
7 (D9)ON
OFF
8 (D8)ON
OFF
SW2 (DIP SW)
NOTE 21 (D7)ON
OFF
2 (D6)ON
OFF
3 (D5)ON
OFF
4 (D4)ON
OFF
5 (D3)ON
OFF
6 (D2)ON
OFF
7 (D1)ON
OFF
8 (D0)ON
OFF
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTIONCHECK
1
23
45
67
8ON
MAC ADDRESS SWITCH SETTING
00004CA4 X X X X 
(HEX)
    FixedSW1-1 (D15)
SW1-2 (D14)
SW1-3 (D13)
SW1-4 (D12)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW1-5 (D11)
SW1-6 (D10)
SW1-7 (D9)
SW1-8 (D8)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW2-1 (D7)
SW2-2 (D6)
SW2-3 (D5)
SW2-4 (D4)ON/OFF
ON/OFF
ON/OFF
ON/OFF
SW2-5 (D3)
SW2-6 (D2)
SW2-7 (D1)
SW2-8 (D0)ON/OFF
ON/OFF
ON/OFF
ON/OFFO N :0   O F F :1
1
23
45
67
8ON 
						

							CHAPTER 5  CIRCUIT CARD INFORMATION
List of Required Circuit Card
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 77
NOTE 1:When the power is on, flip the MB switch to ON (UP position) before plugging/
unplugging the Circuit card.
NOTE 2:Each equipment must have a unique MAC address to distinguish between systems.
Therefore, when more than one PBX is installed in the same network, assign the lower
4 digits of the following MAC address by SW1 and SW2 to prevent duplicate
addresses.
 
00004CA4 XX XX (HEX)
According to the switch setting of SW2 (D7-D0)
According to the switch setting of SW1 (D15-D8)
Fixed 
						

							NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 79
APPENDIX
DEFINITION OF V.24
SIGNAL LEADS
This appendix contains the definition of V.24 signal leads. 
						

							 NEAX2000 IVS2 OAI System ManualPage 80  ND-70922 (E), Issue 1.0
APPENDIX  DEFINITION OF V.24 SIGNAL LEADS
PIN
No.SIGNAL-NAME
DIRECTION
OF SIGNALMEANING
RS-232CJIS C
6361CCITT
V.24ANOTHER
1 AA (FG) 101 GND Frame Ground
2BASD103 TXD
DTE Send Data
3BBRD104 RXD
 DCEReceive Data
4CARS105 RTS
DTE Request to Send
5CBCS106 CTS
 DCEClear to Send
6CCDR107 DSR
 DCEData Set Ready
7 AB SG 102 GND Signal Ground
8 CF CD 109 DCD
 DCEData Channel Receive Carrier
Detect
9 Not used
10 Not used
11 PB Peripheral Busy
12 SCF BCD 122
 DCEBackward Channel Receive
Carrier Detect
13 SCB BCS 121
 DCEBackward Channel Send (OK)
14 SBA BSD 118
DTE Backward Channel Send Data
15 DB ST2 114 TXC (2)
 DCESend Signal Element Timing
16 SBB BRD 119
 DCEBackward Channel Receive
Data
17 DD RT 115 RXC
 DCEReceive Signal Element Timing
18 Not used
19 SCA BRS 120
DTE Backward Channel Send Detect
20 CD ER 108/2 DTR
DTE Data Terminal Ready
21 CG SQD 110
 DCEData Signal Quality Detect
22 CE CI 125 RI
 DCECall Indication
23 CI, CH SRS 112, 111 Data Signal Speed Choice
24 DA ST1 113 TXC (1)
DTE Send Signal Element Timing
25 Not used