NEC Neax 2000 Ivs2 Oai System Manual

							 NEAX2000 IVS2 OAI System ManualPage 44  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for TMF
DESCRIPTION DATA
Specify a chime from Dterm when 
receiving RR signal of TMF.
(1)
(2)Y=7
F1032-F1047: OAI Function Key
No. 0-15
00  : Not sent
01  : To send
Specify a chime from D
term when setting 
up TMF.
(1)
(2)Y=8 
00: Chime before sending terminal
messages (when pressing the OAI
Function key) 
02: Chime after sending terminal
messages
00  : No ring
01  : Ring
Specify the display of guidance on D
term 
when setting up TMF.
(1)
(2)Y=8 
01: Display of guidance before sending
terminal messages (When
pressing the OAI Function key) 
03: Display of guidance after sending
terminal messages
00  : To display
01  : Not displayed
END
CMD7
A 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SCF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 45
DATA ASSIGNMENT FOR SCF
To provide Call Origination with Ringing (FID=3):
To originate a call with Account Code (FID=1, 3, 4, 7):
DESCRIPTION DATA
Assign the Ringing Tone Sending time for 
SCF of OAI.
(1)
(2)Y=0
65: OAI RGT Sending Time 
01-99: 4-396 sec. (4 sec. increments)
If no data is set, the default setting is 12-16 
sec.
DESCRIPTION DATA
Specify the maximum number of digits for 
Account Code.(1)
(2)10
01-16 : 1 digit-16 digits
10 : 10 digits
START
CM41
END
START
CM42
END 
						

							 NEAX2000 IVS2 OAI System ManualPage 46  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SCF
If the Digital Announcement Trunk or Tone is provided, do the following programming:
DESCRIPTION DATA
Assign a Digital Announcement Trunk card 
number to the required LEN.
NOTE 1:The Digital Announcement Trunk 
card number must be assigned to 
the first LEN (Level 0), the third 
LEN (Level 2), the fifth LEN 
(Level 4) and the seven LEN 
(Level 6) of each LT slot.
NOTE 2:EB000 and EB001 are dedicated 
to built-in Digital Announcement 
Trunk of the MP card.(1)
(2)LEN: 000-763
EB002-EB127: Digital Announcement 
Trunk Card No.
For PIM0/1: EB002-EB031
For PIM2/3: EB032-EB063
For PIM4/5: EB064-EB095
For PIM6/7: EB096-EB127 
NOTE 2
Assign the Message Replay timer/Tone 
Sending timer in the OAI terminal mode.
(1)
(2)Y=0 
56: Message Replay Timer/Tone 
Sending Timer
01-99: 4-396 sec. (4 sec. increments)
If no data is set, the default setting is 20-
24 sec.
Assign the function of the Digital 
Announcement Trunk card.
(1)
(2)YY=00 
000-001: Built-in DAT on MP card
002-127: Digital Announcement Trunk
Card No. assigned by CM10
(EB002-EB127)
10: Announcement Service in the OAI
Terminal mode.
Assign the Digital Announcement Trunk 
card number.
(1)
(2)Y=2 
000-127: Message No. 
1 XXX
XXX: 000-127: Digital Announcement
Trunk Card No. 
START
CM10
END
CMD7
CM49
CM41 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SCF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 47
To provide Queue Connection (FID=4):
To provide the system with a monitor number:
DESCRIPTION DATA
Assign the UCD group. 
(1)
(2)Y=0
X-XXXX: Station No.
X-XXXX: Another station No. to be
linked
Assign the Pilot station and Member 
station to queuing for SCF of OAI.
(1)
(2)Y=1 Distinction of Member station from 
Pilot station 
X-XXXX: Station No. 
2: Off Hook suppressed
3: Pilot station (Monitor No.)
* Unable to place or receive a call.
Assign the UCD group number. 
(1)
(2)Y=2 
X-XXXX: UCD Station No. 
00-15: UCD Group 00-15
DESCRIPTION DATA
Assign a virtual station number to be used 
as the monitored number.(1)
(2)000-255: Virtual LEN
X-XXXX: Virtual-Line number
(Assign only one per system.)
Assign the Pilot station and Member 
station to queuing for SCF or OAI.
(1)
(2)Y=1 Distinction of Member station from 
Pilot station 
X-XXXX: Station No. 
2: Member station
3: Pilot station (Monitor No.)
* Unable to place or receive a call.
Assign the UCD group number. 
(1)
(2)Y=2 
X-XXXX: UCD station No. 
00-15: UCD Group 00-15
START
CM17
END
START
CM11
END
CM17 
						

							 NEAX2000 IVS2 OAI System ManualPage 48  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SCF
To provide Announcement Call (FID=5):
DESCRIPTION DATA
Assign a Digital Announcement Trunk card 
number to the required LEN.
NOTE 1:The Digital Announcement Trunk 
card number must be assigned 
to the first LEN (Level 0), the 
third LEN (Level 2), the fifth LEN 
(Level 4) and the seven LEN 
(Level 6) of each LT slot.
NOTE 2:EB000 and EB001 are dedicated 
to built-in Digital Announcement 
Trunk of the MP card.(1)
(2)LEN: 000-763
EB002-EB127: Digital Announcement
Trunk Card No.
For PIM0/1: EB002-EB031
For PIM2/3: EB032-EB063
For PIM4/5: EB064-EB095
For PIM6/7: EB096-EB127
NOTE 2
Assign the Pilot station and Member station 
to queuing for SCF of OAI.
When sending an announcement from the 
beginning on the Multi-Connection 
Announcement Service, set this data to “3”.
(1)
(2)Y=1 Distinction of Member station from
Pilot station 
X-XXXX: Station No. 
2: Originate Suppress
3: Pilot station (Monitor No.)
* Unable to place nor receive a call.
NOTE:2 is for Member station
3 is for Pilot station
Assign the method to send Multi-
Connection Announcement.
When sending an announcement from the 
beginning on the Multi-Connection 
Announcement, set this data to “1”.
(1)
(2)Y=A 
X-XXXX: Pilot station No.
0  : To be sent periodically
1  : To be sent only once
When sending an announcement from the 
beginning on the Multi-Connection 
Announcement, assign the latency time of 
sending the announcement after receiving 
SCF FID=5.
(1)
(2)Y=0 
67: OAI Announcement Connection
Timer
01-32: 4-128 sec. (4 sec. increments)
If no data is set, the default setting is 8-12 
sec.
CM17 START
CM10
A
CM41 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SCF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 49
DESCRIPTION DATA
Assign the function of the Digital 
Announcement Trunk card.
(1)
(2)YY=00
000-001: Built-in DAT on MP card
002-127: Digital Announcement Trunk
Card No. assigned by CM10
(EB002-EB127)
10: Announcement Service for OAI 
16 XX
XX: Message Group No. (02-63) for
Multi-Connection Announcement
Service for OAI.
Assign the Digital Announcement Trunk 
card number.
(1)
(2)Y=2
000-127: Message No. 
1 XXX
XXX: 000-127: Digital Announcement
Trunk Card No.
END
CM49
A
CMD7 
						

							 NEAX2000 IVS2 OAI System ManualPage 50  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for SCF
To provide Conversation Monitoring (FID=6) and Call Conferencing (FID=8):
DESCRIPTION DATA
Assign the Ringing Tone Sending time for 
SCF of OAI.
(1)
(2)Y=0 
65: OAI RGT Sending Time
01-99: 4-396 sec. (4 sec. increments)
If no data is set, the default setting is 12-16 
sec.
START
CM41
END 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for FLF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 51
DATA ASSIGNMENT FOR FLF
DESCRIPTION DATA
Assign the access code to recognize 
Authorization Code for FLF.
NOTE:The access code should be as-
signed to the first one, two or 
three digits of Authorization 
Code. For example:
(1)
(2)Y=0-3
X-XXXX: Access Code
A157
Assign the maximum number of digits for 
Authorization Code.(1)
(2)11 
01-10  : Max. Number of Digits
START
CM20
CM42
A1  2  3  4  5  6
(Authorization Code)
Max. No. of digits 
assigned by CM42>11
Access Code assigned 
by CM20>A157 
						

							 NEAX2000 IVS2 OAI System ManualPage 52  ND-70922 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for FLF
DESCRIPTION DATA
Assign the recognition of AP database by 
RR message.
(1)
(2)Y=A
00
0  : To provide
1  : Not provided
Assign the omission of AP database for 
information added to RR message.
(1)
(2)Y=A
01
0  : Not omitted
1  : To omit
Assign the office number. 
(1)
(2)Y=5
00
Office No. (Max. 4 digits)
Assign the processor for Authorization 
Code/Forced Account Code.(1)
(2)216
1  : AP (PN-AP01)
Assign the processor for a Remote 
Access to System (DISA).(1)
(2)217
1  : AP (PN-AP01)
Allow the Authorization Code/Forced 
Account Code in required Service 
Restriction Class.
(1)
(2)YY=31
00-15: Service Restriction Class A
assigned by CM12 YY=02.
0  : Restrict
1 : Allow
END
CMD7
A
CM08
CM15 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Data Assignment for KTF
NEAX2000 IVS2 OAI System Manual    
ND-70922 (E), Issue 1.0   Page 53
DATA ASSIGNMENT FOR KTF
DESCRIPTION DATA
Assign the OAI function key for starting up 
FLF to a D
term.
(1)
(2)YY=00
My Line No. +   + Key No.
F1032-F1047: OAI Function Key No. 
0-15
START
CM90
END
,