NEC Neax 2000 Ivs2 Oai System Manual
Here you can view all the pages of manual NEC Neax 2000 Ivs2 Oai System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 11
NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 3 CHAPTER 1 GENERAL INFORMATION This chapter explains the OAI system outline and specifications.
Page 12
NEAX2000 IVS2 OAI System ManualPage 4 ND-70922 (E), Issue 1.0 CHAPTER 1 GENERAL INFORMATION System Outline SYSTEM OUTLINE The PBX is equipped with an interface to provide user applications through an external processor. The interface supports RS-232C (Free Wheel) protocol and TCP/IP protocol. OAI with RS-232C For adding the interface with RS-232C, the AP01 card (OAI Interface Card) is required. Figure 1-1 shows the system outline of OAI with RS-232C. Figure 1-1 System Outline of OAI with RS-232C...
Page 13
CHAPTER 1 GENERAL INFORMATION System Outline NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 5 Figure 1-2 External Processor Connection for RS-232C Interface AP01M M2P RS-232C CABLEEXTERNAL PROCESSOR (RS-232C) AP01 EXTERNAL PROCESSOR (RS-232C) (1) External Processor Direct Connection AP01: OAI INTERFACE CARD M : MODEM (2) External Processor Connection via MODEM RS RVS-4(S) CA-A/RS RVS-4(S) CA-C (4 m/13.1 ft.) RS RVS-15(S) CA-A (15 m/49 ft.) Page 6 RS NORM-4 CA-A/RS NORM-4S CA-A (4...
Page 14
NEAX2000 IVS2 OAI System ManualPage 6 ND-70922 (E), Issue 1.0 CHAPTER 1 GENERAL INFORMATION System Outline RS RVS-15 CA-A/RS RVS-15S CA-A RS RVS-4 CA-A/RS RVS-4 CA-C RS RVS-4S CA-A/RS RVS-4S CA-C NOTE:If the external processor does not send DTR or RTS signal, cut the signal lead marked by X in the D-Sub connector (external processor side) as shown in the wiring diagram below. See APPENDIX DEFINITION OF V.24 SIGNAL LEADS. Page 79 05A-TXD 05B-GND 06A-TXC (2) 06A-TXC (2) 06B-RXC 06D-TXC (1) 04B-RXD...
Page 15
CHAPTER 1 GENERAL INFORMATION System Outline NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 7 See APPENDIX DEFINITION OF V.24 SIGNAL LEADS. Page 79 RS NORM-4 CA-A/RS NORM-4S CA-A 05A-TXD 05B-GND 05C-DTR 06A-TXC (2) 06B-RXC 06D-TXC (1) 04B-RXD 04A-RTS 02-RXD 01-GND 20-DSR 15-TXC (1) 17-RXC 03-TXD 04-DCD 24-TXC (2) 02B-GND 03A-DSR 03B-CTS 02A-DCD 01C-LALB 07-GND 06-DTR 05-CTS 08-RTS 18-LALB G: GROUND (4 m/13 ft.) DC B A 06 TXC (1) RXC TXC (2) 05 DTR GND TXD 04 (RT) RXD RTS 03 (ST) CTS...
Page 16
NEAX2000 IVS2 OAI System ManualPage 8 ND-70922 (E), Issue 1.0 CHAPTER 1 GENERAL INFORMATION System Outline OAI with TCP/IP-Ethernet The PBX is equipped with an interface to transmit/receive the control signals between the PBX and the Ethernet. The interface supports TCP/IP protocol. For adding the interface with TCP/IP, the ETHER card (CC01) (Ethernet Gateway Controller) is required in addition to the AP01 card. Figure 1-3 shows the system outline of OAI with TCP/IP-Ethernet. Figure 1-3 System...
Page 17
CHAPTER 1 GENERAL INFORMATION System Specifications NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 9 SYSTEM SPECIFICATIONS RS-232C Interface Specification MODEM Specification Table 1-1 RS-232C Interface Specification DESCRIPTION SPECIFICATION REMARKS Transmission Speed 150, 300, 600, 1200, 2400, 4800 or 9600 bps Synchronization Asynchronous Transmission Mode Full Duplex Parity No Parity Stop Bit 1-Stop Bit Kind of Code JIS (8-bit) Transmission Procedure Free Wheel Table 1-2 MODEM...
Page 18
NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 11 CHAPTER 2 INSTALLATION This chapter explains the hardware installation procedure to provide OAI interface to the PBX.
Page 19
NEAX2000 IVS2 OAI System ManualPage 12 ND-70922 (E), Issue 1.0 CHAPTER 2 INSTALLATION Precautions PRECAUTIONS Static Electricity Guard You must wear a grounded wrist strap to protect circuit cards from static electricity. Figure 2-1 Static Electricity Guard (1 of 2) WHEN PLUGGING/UNPLUGGING A CIRCUIT CARD WHEN HOLDING A CIRCUIT CARD PBX WRIST STRAP FRAME GROUND SCREW CARD FRONT NEVER TOUCH THE COMPONENTS OR SOLDERED SURFACE WITH BARE HANDS.
Page 20
CHAPTER 2 INSTALLATION Precautions NEAX2000 IVS2 OAI System Manual ND-70922 (E), Issue 1.0 Page 13 Figure 2-1 Static Electricity Guard (2 of 2) WHEN MAKING A SWITCH SETTING ON A CIRCUIT CARD WHEN CARRYING A CIRCUIT CARD The mark shown below is attached to the sheet for work in which circuit cards are handled. When engaging in such work, the installer must be careful not to cause damage by static electricity. WEAR A WRIST STRAP AND PERFORM THE WORK ON A GROUNDED CONDUCTIVE WORK SURFACE....