NEC Neax 1000 Ivs Very Small Platform System Manual
Have a look at the manual NEC Neax 1000 Ivs Very Small Platform System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24219 CHAPTER 3 Page 127 Revision 2.0 NAP-200-013 Sheet 1/1 Mounting of Front Cover 1. MOUNTING FRONT COVER Mount the Front Cover onto PIM using the provided screws as shown in Figure 013-1. Figure 013-1 Mounting Front Cover PIM FRONT FRONT COVER
CHAPTER 3 NDA-24219 Page 128 Revision 2.0 This page is for your notes.
NDA-24219 CHAPTER 4 CHAPTER 4 OFFICE DATA P ROGRAMMING
CHAPTER 4 NDA-24219 Page 130 Revision 2.0 1.2.2 Station Data In this table, the following data are required. • Station Number: Station numbers (up to four digits), specified in the Numbering Plan Table, are assigned. For the Multiline Terminal station, specify the Primary Extension Number. • Type of Telephone The type of station telephone set is specified as shown below. TYPE OF TEL DESCRIPTION DP................................... Dial Pulse Telephone set PB ................................... DTMF Telephone set Multiline Terminal.......... Multiline Terminal set • SERVICE CLASS-A/B/C Specify the service class (1-15) programmed in the Service Restriction Data Table. • RESTRICTION CLASS-DAY/NIGHT Specify the Trunk Restriction Class as shown below. 1: Unrestricted 2: Non-Restricted-1 3: Non-Restricted-2 4: Semi-Restricted 1 5: Semi-Restricted 2 6: Restricted 1 7: Restricted 2 8: Fully-Restricted • DIT TRUNK NUMBER In the case of the DIT (Direct-In Termination) station, specify the trunk number connected. 1.2.3 Trunk Data In this table, the following data are required: • ACCESS NUMBER Specify the access code for the trunks. • DESTINATION Specify the distant office such as Central Office (Public Exchange), Tie Line, etc.
NDA-24219 CHAPTER 4 Page 131 Revision 2.0 • NUMBER OF LINE Specify the number of trunks to be provided with each route (IC-Incoming, OG-Outgoing, BW-Bothway). • DP/PB Specify the type of address signal from/to distant office, as shown below. TYPE OF TEL DESCRIPTION DP................................... Dial Pulse PB ................................... DTMF Signal • KIND OF SIGNAL Specify the kind of signaling system such as Ring Down, Loop, E & M etc. at the line. 1.2.4 Station Hunting Group Data This data table requires the following data: • KIND OF STATION HUNTING Specify the kind of the Station Hunting System (Pilot/Circular/Switch Back). In the case of the Pilot Sys- tem, specify the Pilot Station Number. • SECRETARY STATION Specify the Secretary Station Number, if provided. • STATION NUMBER Specify the station numbers to be assigned to the station hunting group with the following conditions. (1) Up to 60 stations can be assigned per Station Hunting Group. (2) There is no limitation to the number of Station Hunting Groups. The same one station cannot be assigned to multiple Hunting Groups. 1.2.5 Call Pickup Group Data The station number to be assigned to the Call Pickup Group with the following conditions. (1) Up to 60 station can be assigned per Call Pickup Group. (2) There is no limitation to the number of Call Pickup Groups. (3) The same one station cannot be assigned to multiple Call Pickup Groups.
CHAPTER 4 NDA-24219 Page 132 Revision 2.0 1.2.6 Speed Calling-System Data This data table requires the abbreviated code and the stored number to be sent out. A maximum stored number of 28 digits can be assigned. 1.2.7 Port Assignment Table Specify the station number or trunk number corresponding to the LEN (Line Equipment Number) as shown in Table 4-2. The LEN means physical location number within the PIM. Table 4-2 Port Assignment Method CARD TO BE ASSIGNEDPORT ASSIGNMENT TABLE REMARKS PN-8LC PN-8DLC PN-8COT• For PN-8DLC, specify primary extension numbers of multiline terminal as follows: PN-4LC PN-4DLC• Station number must be assigned to 1st LEN (LEVEL 0) through 4th LEN (LEVEL 3) of each LT s l o t . • For PN-4DLC, specify primary extension numbers of multiline terminal as follows: LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Station No. LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 207 0007 206 0006 205 0005 204 0004 203 0003 202 0002 201 0001 200 0000/Trunk No. (D000-D255)FXXX Primary Extension Number LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 –0004 203 0003 202 0002 201 0001 200 0000 Station No. used FXXX Primary Extension Number
NDA-24219 CHAPTER 4 Page 133 Revision 2.0 PN-AUC PN-2DLC• Station number must be assigned to 1st LEN (LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT slot. • For PN-2DLC, specify primary extension numbers of multiline terminal as follows: PN-4COT PN-4DIT• Trunk number must be assigned to 1st LEN (LEVEL 0) through 4th LEN (LEVEL 3) of each LT s l o t . PN-AUC PN-2ODT• Trunk number must be assigned to 1st LEN (LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT slot. Table 4-2 Port Assignment Method (Continued) CARD TO BE ASSIGNEDPORT ASSIGNMENT TABLE REMARKS LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00–0007 – 0006 – 0005 – 0004 –0003 – 0002 201 0001 200 0000 Station No. assigned FXXX Primary Extension Number LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 D003 0003 D002 0002 D001 0001 D000 0000assigned Trunk No. (D000-D255) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 D003 0003 D002 0002 D001 0001 D000 0000 Trunk No. assigned(D000-D255)
CHAPTER 4 NDA-24219 Page 134 Revision 2.0 PN-2DAT • Card number must be assigned to 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. PN-8RST • Card number must be assigned to 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. Note:When using the internal DTMF Receiver on the MP card, assign Card No. E200 to LEN No. 0124. PN-DK00 • Card number must be assigned to 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. • Card numbers of External Equipment Interface are E800-E807. • Card numbers of External Key Interface are E900- E915. Table 4-2 Port Assignment Method (Continued) CARD TO BE ASSIGNEDPORT ASSIGNMENT TABLE REMARKS LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 – 0003 EB001 0002 – 0001 EB000 0000 Card No. assigned(EB000-EB031) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 – 0003 E201 0002 – 0001 E200 0000 Card No. assigned(E200-E203) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 – 0003 E801 0002 – 0001 E800 0000 Card No. assigned(E800-E807) (E900-E915)
NDA-24219 CHAPTER 4 Page 135 Revision 2.0 PN-CFT• Card number must be assigned to 1st LEN (LEVEL 0) of each LT slot. PN-2DPC • To assign data station number to PN-2DPC by CM1A, specify primary extension number of multiline terminal as a dummy station number. • Primary extension number must be assigned to 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. PN-TNT • Card number must be assigned to 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. Table 4-2 Port Assignment Method (Continued) CARD TO BE ASSIGNEDPORT ASSIGNMENT TABLE REMARKS LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 – 0003 – 0002 – 0001 ED00 0000 Card No. assigned(ED00-ED03) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 – 0003 F201 0002 – 0001 F200 0000 Primary assigned (FX-FXXXX) Extension No. LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00–0007 – 0006 – 0005 – 0004 – 0003 DA09 0002 – 0001 DA00 0000 Card No. assigned(DA00-DA09)
CHAPTER 4 NDA-24219 Page 136 Revision 2.0 PN-2AMP • Card number must be assigned to the 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. PN-2ILC • ISDN circuit station number must be assigned to 1st LEN (LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT slot. Table 4-2 Port Assignment Method (Continued) CARD TO BE ASSIGNEDPORT ASSIGNMENT TABLE REMARKS LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 – 0003 C101 0002 – 0001 C100 0000 Card No. assigned(C100-C163) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4LT00 – 0007 – 0006 – 0005 – 0004 – 0003 – 0002 201 0001 200 0000 ISDN Circuit assignedStation No.