NEC Neax 1000 Ivs Very Small Platform System Manual
Have a look at the manual NEC Neax 1000 Ivs Very Small Platform System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24219 CHAPTER 3 Page 107 Revision 2.0 NAP-200-008 Sheet 3/10 Switch Setting of Circuit Card (3) Switch Setting (see Table 008-4) Table 008-4 PN-CP03 (MP) Card Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW3 (Rotary SW) 0 - FOn Line (Call processing is in progress) 2Off Line (Call processing is stopped) • I/O port: Depending on CM40 YY=08 3Off Line (Call processing is stopped) • I/O port: 1200bps (Fixed) B For clearing office data C For setting resident system program 1, 4 - 9 A, D - FNot used SW1 (Push SW) For initializing CPU SW2 (Piano Key SW) 1 ONKF Mode MF/PF Mode 2, 3Selection of PLO (Phase Locked Oscillator) • When using internal PLO of MP card: 0 ON OFF 4 3 2 1 OFF SWITCH OFFON1.5MHz clock [For PN-24DTA/PN-24DTA-A] 192kHz clock [For PN-BRTA] 2MHz clock [For PN-30DTC] Not used OFF OFF ON OFF ON ON FUNCTION 23NUMBER
CHAPTER 3 NDA-24219 Page 108 Revision 2.0 NAP-200-008 Sheet 4/10 Switch Setting of Circuit Card The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. Note:Set the groove on the switch knob to the desired switch position.Table 008-4 PN-CP03 (MP) Card Switch Settings (Continued) SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW2 (Piano Key SW) 2, 3• When using the PLO card (PN-CK00): SW2-2 SW2-3OFF ON • When not using the internal PLO and the PLO card: SW2-2 SW2-3OFF OFF 4ONWhen using RS1 port for built-in MODEM. OFFWhen using RS1 port for RS-232C. VR (Rotary SW) Variable Resistor for External Hold Tone Source (0 - 20 K W: Clockwise) JP0 (Jumper pin) For normal operation Note:Do not remove this jumper. The power to RAM will be removed causing loss of Office Data Pro- gramming. DOWNNot used JP1 (Jumper pin) For normal operation Note:Do not relocate this jumper when power is turned on. DOWN For using External Tone Source ON OFF 4 3 2 1 20 0 Front UP Front UP
NDA-24219 CHAPTER 3 Page 109 Revision 2.0 NAP-200-008 Sheet 5/10 Switch Setting of Circuit Card CAUTION: When the operating power is being supplied to this circuit card, do not plug/unplug this circuit card into/from its mounting slot. 3. PZ-PW86 (PWR) (1) Locations of Lamps, Switches, and Connectors (see Figure 008-2) Figure 008-2 PZ-PW86 (PWR) Card FRONT VIEW BATT2 MN MJ ONBATTERY SIDE VIEW GND –27V FG OFFON 240VAC 100/120VAC 2ON 2 1 ON SW301 START SIG 1 SW1 BATT1 AC INPUTMODE SW102 • PZ-PW86(C) AT T E N T I O NContents Static Sensitive Handling Precautions Required
CHAPTER 3 NDA-24219 Page 110 Revision 2.0 NAP-200-008 Sheet 6/10 Switch Setting of Circuit Card Figure 008-2 PZ-PW86 (PWR) Card (Continued) (2) Lamp Indications (see Table 008-5) Table 008-5 PZ-PW86 (PWR) Card Lamp Indications LAMP NAME COLOR FUNCTION MJ Red Lights upon occurrence of a major fault. MN Yellow Lights upon occurrence of a minor fault. ON Green Remains lit while the power is on. FRONT VIEWBATT2 MN MJ ON BATTERY SIDE VIEW GND –27V FG OFFON 240VAC 100/120VAC2ON 2 1 ON SW102 START SIG 1 SW1 BATT1 MODE SW301 (CN103) SIG (CN103) • PZ-PW86(D) AC INPUT AT T E N T I O NContents Static Sensitive Handling Precautions Required
NDA-24219 CHAPTER 3 Page 111 Revision 2.0 NAP-200-008 Sheet 7/10 Switch Setting of Circuit Card (3) Switch Settings (see Table 008-6) The figure in the SWITCH NAME column and the position in in the SETTING POSITION col- umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. Table 008-6 PZ-PW86 (PWR) Card Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK Mode (Piano Key SW) 1Always set to OFF 2Standard setting for equalize charging (set to equalize for Gel cell or no battery). OFF Float charging, for vented batteries only. SW1For turning AC power and the battery on OFFFor turning AC power and the battery off SW102 BATTERY START PRESS MO- MENTARILYTo start each PIM on battery power, when AC power is not provided (switch “SW” must be ON) AC INPUT: 180 V - 264 V DOWNAC INPUT: 180 V - 264 V SW301 1ONCR Voltage: 75 Vrms OFFCR Voltage: 90 Vrms 2ONFrequency: 20 Hz OFFFrequency: 25 Hz 1 2 ON OFF ON ON (–) OFF (O) ON 240 VAC 100/120 VAC UP 2 1ONOFF 20Hz 25Hz 75V 90V
CHAPTER 3 NDA-24219 NAP-200-008 FRONT V IEW ST ART SW1 SW102 BATT0 CN103
NDA-24219 CHAPTER 3 Page 115 Revision 2.0 NAP-200-009 Sheet 1/3 Mounting Circuit Cards 1. MOUNTING PROCEDURE (1) For testing, turn on “SW1” switch on the PZ-PW86/PZ-PW112 card. Make sure that “ON” lamp (green) is lit. See Figure 009-1. (2) Turn off “SW1” switch. Figure 009-1 PZ-PW86/PZ/PW112 Card Lamp Indication PZ-PW86/PW112 ON OFFSW SWITCH ON LAMP (GREEN)MN MJ ON
CHAPTER 3 NDA-24219 Page 116 Revision 2.0 NAP-200-009 Sheet 2/3 Mounting Circuit Cards (3) Before mounting the circuit cards, confirm the following items. • Wrist Strap is connected Frame Ground. • Switch setting of circuit cards is already completed (Refer to the Circuit Card Manual). • “SW1” switch of PZ-PW86PZ/PW112 Card is turned off. (4) Mount circuit cards into their mounting positions according to the “Bay Face Layout” and “Port Assign- ment Table” given in the System Data Sheet. Figure 009-2 shows the mounting method of circuit cards. Figure 009-2 Mounting Circuit Cards CARD FRONT SIDE WRIST STRAP TO FRAME GROUND CONNECTION (SEE FIGURE 3-1) CARD CONTACT SIDE