Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways User Guide

MultiVOIP User Guide Mechanical Installation & Cabling
71
3. Connect a network cable to the ETHERNET 10BASET connector on
the back of the MultiVOIP. Connect the other end of the cable to your
network.
4. If you are connecting a station device such as an analog telephone, a
fax machine, or a Key Telephone System (KTS) (FXS interface), or a
PBX extension (FXO interface) to your MultiVOIP, connect one end of
an RJ-11 phone cord to the Channel 1 FXS/FXO connector on the back
of the MultiVOIP and the other...

Mechanical Installation & Cabling MultiVOIP User Guide
72
Cabling Procedure for MVP210
Cabling involves connecting the MultiVOIP to your LAN and telephone
equipment.
1. Connect the power cord supplied with your MultiVOIP to the power
connector on the back of the MultiVOIP and a live AC outlet as
shown in Figure 3-11.


	


	
	

	
	
	
		
	
		
	
E&MFXS/FXOFXS/FXORS232
COMMAND 10/100POWER ETHERNET
E&M
	



	
	...

MultiVOIP User Guide Mechanical Installation & Cabling
73
will define the interface in the Interface dialog box in the software
when you configure the unit. 
If you are connecting an E&M trunk  from a telephone switch to your
MultiVOIP, connect one end of an RJ-45 phone cord to the Channel 1
E&M connector on the back of the MultiVOIP and the other end to
the trunk.  Verify that the E&M Type in the E&M Options group of
the Interface dialog box is the same as the E&M trunk type support
by the telephone...

74
Chapter 4: Software Installation 

MultiVOIP User Guide Software Installation
75
Introduction
Configuring software for your MultiVOIP entails three tasks:
(1) loading the software onto the PC (this is “Software Installation and
is discussed in this chapter),
(2) setting values for telephony and IP parameters that will fit your
system (this is “Technical Configuration” and it is discussed in Chapter
5 for T1/E1 MultiVOIP units and in Chapter 6 for analog MultiVOIP
units), and
(3) establishing “phonebooks” that contain the various dialing...

Software Installation MultiVOIP User Guide
76
2. Insert the MultiVOIP CD into your CD-ROM drive.  The CD should
start automatically.  It may take 10 to 20 seconds for the Multi-Tech
CD installation window to display.   
If the Multi-Tech Installation CD window does not display
automatically, click My Computer, then right click the CD ROM
drive icon, click Open, and then click the Autorun icon.
3. When the Multi-Tech Installation CD dialog box appears, click the
Install Software icon. 

MultiVOIP User Guide Software Installation
77
4. A ‘welcome’ screen appears.
Press Enter or click Next to continue. 

Software Installation MultiVOIP User Guide
78
5. Follow the on-screen instructions to install your MultiVOIP software.
The first screen asks you to choose the folder location of the files of
the MultiVOIP software.
Choose a location and click Next. 

MultiVOIP User Guide Software Installation
79
6. At the next screen, you must select a program folder location for the
MultiVOIP software program icon.
Click Next.  Transient progress screens will appear while files are
being copied. 

Software Installation MultiVOIP User Guide
80
7.  On the next screen you can select the COM port that the command
PC will use when communicating with the MultiVoip unit. After
software installation, the COM port can be re-set in the MultiVoip
Software (from the sidebar menu, select Connection | Settings to
access the COM Port Setup screen or use the keyboard shortcut Ctrl
+ G).
NOTE:  If the COM port setting made
here conflicts with the actual COM
port resources available in the
command PC, this error...