Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways User Guide

MultiVOIP User Guide Mechanical Installation & Cabling
61
Unpacking Your MultiVOIP
When unpacking your MultiVOIP, check to see that all of the items
shown are included in the box.  For the various MultiVOIP models, the
contents of the box will be different.  Study the particular illustration
below that is appropriate to the model you have purchased.  If any box
contents are missing, contact MultiTech Tech Support at 1-800-972-2439.    
Unpacking the MVP2410/3010
Figure 3-1:  Unpacking the MVP2410/3010 

Mechanical Installation & Cabling MultiVOIP User Guide
62
Unpacking the MVP2400
Voic e/Fax over IP Networks200
Quick Start
Guide
Figure 3-2:  Unpacking the MVP2400 

MultiVOIP User Guide Mechanical Installation & Cabling
63
Unpacking the MVP410/810
Voice/Fax over IP Networks
RCV XMT CO L LNKX M T R C V XS G R SG XMT RCV XSG RSG XMT RCV XSG RSG XMT RC V XSG RSG
XMT RC V XSG RSGXMT RCV XSG RSG
XMT RCV XSG RSG
Vo ic e/Fax  5 Voice /Fax  6 Voic e/ Fax  7 Voic e/Fax  8
Voi ce/ F ax 1
Vo ic e/Fax  2 Voic e/ Fax  3Voi c e/F ax  4 Ether net
BootPowerXMT RCV XSG RSG
Quick Start
Guide
Figure 3-3:  Unpacking the MVP410/810 

Mechanical Installation & Cabling MultiVOIP User Guide
64
Unpacking the MVP210
Voic e/Fax over IP Networks200
Quick Start
 Guide
Figure 3-4:  Unpacking the MVP210 

MultiVOIP User Guide Mechanical Installation & Cabling
65
Rack Mounting Instructions for
MVP2410/3010 & MVP410/810
The MultiVOIPs can be mounted in an industry-standard EIA 19-inch
rack enclosure, as shown in Figure 2-5.  
Figure 3-5: Rack-Mounting (MVP2410/3010 or MVP410/810) 

Mechanical Installation & Cabling MultiVOIP User Guide
66
Safety Recommendations for Rack Installations
Ensure proper installation of the unit in a closed or multi-unit enclosure
by following the recommended installation as defined by the enclosure
manufacturer. Do not place the unit directly on top of other equipment
or place other equipment directly on top of the unit.  If installing the
unit in a closed or multi-unit enclosure, ensure adequate airflow within
the rack so that the maximum recommended...

MultiVOIP User Guide Mechanical Installation & Cabling
67
19-Inch Rack Enclosure Mounting Procedure
Attaching the MultiVOIP to a rack-rail of an EIA 19-inch rack enclosure
will certainly require two persons.  Essentially, the technicians must
attach the brackets to the MultiVOIP chassis with the screws provided,
as shown in Figure 3-6, and then secure unit to rack rails by the
brackets, as shown in Figure 3-7.  Because equipment racks vary, screw
for rack-rail mounting are not provided.  Follow the...

Mechanical Installation & Cabling MultiVOIP User Guide
68
Cabling
Cabling Procedure for MVP2410/3010
Cabling your MultiVOIP entails making the proper connections for
power, command port, phone system (T1/E1 line connected to PBX or
telco office), and Ethernet network.  Figure 3-8 shows the back panel
connectors and the associated cable connections.  The following
procedure details the steps necessary for cabling your MultiVOIP.
1. Connect the power cord to a live AC outlet, then connect it to the...

MultiVOIP User Guide Mechanical Installation & Cabling
69
3. Connect a network cable to the Ethernet connector on the back of the
MultiVOIP.  Connect the other end of the cable to your network.
4. Turn on power to the MultiVOIP by setting the power switch on the
right side panel to the ON position.  Wait for the Boot LED on the
MultiVOIP to go off before proceeding.  This may take a couple of
minutes.
Proceed to Chapter 4 “Software Installation.”
Cabling Procedure for MVP2400
Cabling your MultiVOIP...

Mechanical Installation & Cabling MultiVOIP User Guide
70
3. Connect a network cable to the Ethernet connector on the back of the
MultiVOIP.  Connect the other end of the cable to your network.
4. Turn on power to the MultiVOIP by setting the power switch on the
right side panel to the ON position.  Wait for the Boot LED on the
MultiVOIP to go off before proceeding.  This may take a couple of
minutes.
Proceed to Chapter 4 “Software Installation.”
Cabling Procedure for MVP410/810
Cabling involves...