Mitel Sx 50 Dpabx Instructions Guide

Remote Maintenance, Administration and Test System (RMATS) 
9104-091301-NA Issue 5  301 2-2 Revision 0  

3.1 Install an RMATS module in any one of the four module positions on a Universal 
Card. Install the Universal Card in any card slot. 
RMATS must be programmed at the SX-50 DPABX prior to use: 
* Program RMATS Modem Access Code. Default is 498. (Command 110, Feature Ac- 
cess Codes, Register 26). 
0 Program the RMATS Security Code. Default is 0246813579. Command 192, 
RMATS Security Code Programming, Register 1, fields b,c,d,e,f = digits l-5. Regis- 
ter 2, fields b,c,d,e,f = digits 6-10. 
* Program the...

Remote Maintenance, Administration and Test System (RMATS) 
9104-091-301-NA Issue 5  301 3-2 
Revision 0  

4.1 To access RMATS: 
1. From within the DPABX, dial the RMATS Access Code. 
2. Call the Attendant. Have the Attendant dial the RMATS Access Code and connect 
the call. 
3. If a DISA trunk is programmed, use it to gain access to the DPABX and dial the 
RMATS Access Code. 
4. If a Direct-In Line is programmed, use it to gain direct access to RMATS from out- 
side the PABX. 
4.2 When the RMATS modem is accessed, it returns a carrier tone. When using an 
acoustically-coupled modem, put the handset into the...

Remote Maintenance, Administration and Test System (RMATS) 
4.4 
level of both PBX Programming and Attendant Functions menus the user can 
for a list of the RMATS commands available at that level. 
4.5 In both PBX Programming and Attendant Functions menus, the user can enter 
a list of system commands. In the Attendant Functions menu a list of the ava 
Attendant Functions is given. In the PBX Programming menu a list of the CDE 
Commands is given. 
4.6 RMATS provides access to the Attenda ctions listed in...

System Operation 
user can enter the number of a programmed register, with no following . The 
contents of that register will be immediately displayed. Again, the cursor will be at the 
left of the display. 
Unlike the Console display, the RMATS terminal displays all 26 digits in the Digit 
Comparison Table and the Digit Modification Table. 
There are two additional commands used for programming the Digit Modification Table 
digit strings. These are for Pause and for Wait For Dial Tone. 
The Time-of-Day...

Remote Maintenance, Administration and Test System (RMATS) 
Table 4-1 
Unbusy Trunk 
Unbusy DTMF Generator 
Unbusy DTMF Receiver 52 
53 
Unbusy Dial Tone Detector 
I 54 
Abbreviated Dialing Entry Viewing 
Abbreviated Dialing Entry Programming 60 
65 
Printer Options 
I 75 
I 80 
Main Level Commands 
display Register contents 
S 1 display Summary of Commands 
301 4-4 Revision 0 9104-09-l-301-NA Issue 5  

System Operation 
Table 4-3 Sample ats 
2. Enter 501  TRUNK PROGRAMMING 
CMD 501 >> 
3. Enter  ABCDEFGHIJ 
, 
10100010 
n 
’ 
4. Enter 1 ~SDXSD>~ cx1>1  1 1 1 
ABCDEFGHIJ 
ttendant Functions 
Enter 11  AF >>li SWITCH TO NIGHT SER- 
9104-091-301-NA Issue 5 
Revision 0 301 4-5  

Remote Maintenance, Administration and Test System (RMATS) 
PRIMARY SELECTION MENU 
P PROGRAMMING FUNCTIONS 
A ATTENDANT FUNCTIONS 
RMATS LOGOFF 
Page 2 of 2 
301 4-6 
Revision 0 9104-091-301-NA Issue 5  

‘;, F-T ra cl emark of Mite1 Corporation. 
opyright 1993 Mite1 Corporation. 
All rights reserved. 
Printed in Canada.