Mitel Sx-2000 Integrated Communications System Control Sheet Manual

Important Safety Instructions 
Table 1-7 SX-2000 SG System Sub-assemblies 
(continued) 
Page 2 of 3 
9125-060-203-NA Issue 1 
Revision 0 203 l-27  

Safety instructions 
Table 1-7 SX-2000 SG System Sub-assemblies 
(continued) 
Marketing Number 
Description / Common Name Engineering Minimum 
Number Revision 
MM080BA 
FILTER HOUSING 1070806BA A 
MM082AA CABLE TROUGH KIT 1 1070826AA A 
MM089AB FILLER CARD 132887501 B 
MM136AA CABLE DUCT 1071366AA A 
MP91 OFA CONTROL CONVERTER II 1079106FA A 
MPSllCA PERIPHERAL CONVERTER 1079116CA A 
MP912BA DC CONVERTER 1255493BA A 
MK149AA ROOF SCREEN ASSEMBLY 134336601 A 
Page 3 of 3 
Note: DSUs listed in Table l-11...

Important Safety Instructions 
Table l-8 SX-2000 S System Sub-assemblies 
I I I 
MA308AA 1 CEPT INTERFACE ASSEMBLY 
1 1210563AA A 
I 
MA309AA 
DS-1 INTERFACE ASSEMBLY 1202623AA A 
MA31 OAA SYSTEM ID MODULE 121060601 B 
MA320AA CONTROL CABINET 133182601 A 
I 
I I 
MA321AA 1 PERIPHERAL CABINET 1 133186601 A 
I 
2nd CABINET CONTROL COMMUNICATION KIT 
I I 
MP914AA 1 AC CONVERTER 1258033AA 1 3 
I 
Note: DSUs listed in Table l-l 1 and PlCs listed in Table l-l 2 are also suitable for use in the SX-2000 S...

Safety Instructions 
Table l-9 SX-2000VS System Sub-assemblies 
MP912BA DC CONVERTER 1255493BA A 
MP914AA AC CONVERTER 1258033AA 3 
Note: DSUs listed in Table l-11 and PlCs listed in Table l-l 2 are also suitable for use in the SX-ZOffOVS system. 
203 l-30 
Revision 0 9125-060-203-NA Issue 1  

Important Safety Instructions 
Table I-10 SX-2UUO FD System Sub-assemblies 
Note: DSUs listed in Table 1-11 and PlCs listed in Table 1-12 are also suitable for use in the SX-2000 FD system. 
912546&203-NA Issue 1 Revision 0 203 l-31  

Safety Instructions 
I Table I-11 Digital Service Unit (DSU) Cards 
Marketing 
Description / Common Name Engineering Minimum 
Number Number Revision 
MC260AA CONFERENCE 
1072603AA A 
1 MC262AA ( ADVANCE TONE DETECTOR 
1 1072623AA 1 B 1 
MC263AA 1 DS-1 FORMATTER 
I I 
1 1072633AA 1 B 
1 
MC264AA CEPT FORMATTER 1072643AA B 
MC265AA DATA TRANSCEIVER (SEE NOTE) 1072653AA A 
MC266AA 1 COMMUNICATION PROCESSOR 
‘Note: Not used in the SX-2000 FD system. 
1072663AA 4 
I 
Table 1-12 Peripheral Interface Circuit...

Important Safety Instructions 
Installation of Telecommunications Wiring 
1.7 Telecommunications wiring to this product shall conform to all applicable safety and 
electrical wiring regulations. Installation of telecommunications wiring shall be 
performed following precautions in accordance with standard industry practice. The 
precautions to be followed include: 
1. Never install telephone wiring during a lightning storm. 
2. Never install telephone jacks in wet locations unless the jack is...

Safety Instructions 
Examples of installations which shall not be permitted for connection to these interfaces 
are those which: 
(a) Require protectors in accordance with the National Electrical Code for the United 
States, NEC, NFPA / ANSI 70, Article 800-30, or, 
(b) Are “Exposed Plant” as defined in the Canadian Electrical Code -CSA C22.1, para- 
graph 60-I 00 which states; “Exposed plant means where any portion of the circuit 
is subject to accidental contact with electric lighting or power...

SX-2000s INTEGRATED 
COMMUNICATIONS SYSTEM 
Commissioning 
la 
AtoZ KELLATRONICS, INC 
I 
TM, @-Trademark ol MM Corpomtlon. 
0 CopyrIght WBZ, MM CorponUon. 
All rights resewed. 
PrInted In Canada 
a MITE2  

ii NOTICE 
The information contained in this document is believed to be accurate in all re- 
spects but is not warranted by Mite1 Corporation (MITELB). The information is 
subject to change without notice and should not be construed in any way as a 
commitment by Mite1 or any of its affiliates or subsidiaries. Mite1 and its affiliates 
and subsidiaries assume no responsibility for any errors or omissions in this doc- 
ument. Revisions of this document or new editions of it may be issued to incor- 
porate...