Mitel Sx-2000 Integrated Communications System Control Sheet Manual

5 
’ SX-ZOOOSGICS 
COMMISSIONING 
Install Circuit Cards 
Ensure that the Main and Peripheral Control cards, the Peripheral Interface cards 
(PICs), and the Digital Service Unit (DSU) cards are installed in the correct card slots 
before loading the commissioning software. The following chart describes the card 
installation procedure for the SX-2000 SG (Chart 5-1) system. 
Chart 5-l Install Circuit Cards on the SX-2000 SG ICS 
Apply power 
to the system by setting the following 
circuit breakers to ON:...

Commissioning 
Chart 5-l Install Circuit Cards on the SX-2000SG ICS 
(continued) 
Step Action Comments 
a. Insert all Digital Service Units (DSUs) into their Refer to Figure 5-l. 
appropriate slots. 
Slots 29 through 32 on the Control 
Shelf. 
Additional DSUs may be installed 
in a DSU Shelf, if present. 
9. Go to Chart 5-2 for the procedure to load 
commissioning software. 
Page 2 of 2 
204 5-2 
Revision 0 9125-060-204-NA Issue 1  

m IA 
SX-2000 SG ICS Commissioning 
(A) PEAPHERALSHELP 
1 2 3 4 5 6 7 8 810 11 12 13 14 15 16 17 18 18 20 21 22 23 24 25 26 27 23 28 30 31 32 33 
I 
PERlPHERAL INTERFACE CARDS I I 
I I 
PERIPHERAL 
SWlTCH 
12345s 7 8 8 10 11 12 13 14 15 16 17 18 18 20 21 22 23 24 25 26 27 23 28 30 31 32 33 
MAIN CONrFiOL COMPLEX MESSAGE SWITCH CIRCUIT SWKCH DlGKILSEB’lCE UNITS 
Notel. 
N&P. 
Note 3. 
Note 4(a). 
pg p 
Note 6: 
Note7. The minlmlon system omfiguration must have cards indicated by * symbd In&&d in shelves...

Commissionina 
load Commissioning Software 
5.2 The following chart details the steps required to install commissioning software on 
the SX-2000 SG system. 
Chart 5-2 Load Commissioning Software On Plane A 
step Action Comments 
1. Remove the “Wriie Protect” tab on the Commissioning The floppy diskette and the hard 
floppy diskette. disks are protected from 
corruption since by default when 
tests are run on these devices 
only designated test pages are 
accessed by them. 
2. Insert the commissioning...

m Ii 
SX-2000 SG ICS Commissioning 
Chart !5-2 Load Commissioning Sofhvare On Plane A 
(continued) 
and reinsert the incorrectly 
configured card. Enter the 
CONFIG command to generate a 
new report. If the card still does 
ENTER SPACE TO 
TO RETURN TO COMMAND MODE> 
PERIPHERAL SWITCH HARDWARE 
CONFIGURATION IN PROGRESS 
owing message: 
Any commands entered at the Maintenance Terminal 
after this point require the Maintenance Terminal 
RETURN key be pressed. Any command entered 
hereafter is assumed to...

Commissioning 
Main and Subsystem Control Tests 
5.3 Main and Subsystem Control Tests are performed on the SX-ZOOOSG system as 
described in the following chart, 
Note: When the Main Control subsystem tests are run, the Mass Storage System is also 
tested.The ‘Write Protect” tab on the commissioning diskette should be removed prior to 
running these tests. The diskette is automatically protected from corruption, since the 
system knows where the load is located and will not overwrite it, even if the disk...

SX-2000 SG ICS Commissioning 
Chart 5-3 SX-2000 SG Main and Subsystem Control Tests 
(continued) 
Step Action Comments 
(c&t) if errors are detected, an error message is returned. if a card fails a test, remove and 
Refer to Appendix A. for a list of error messages. m-insert the failed card, and rerun 
the test on that slot by issuing the 
following command: 
TEST (slot number) 
if the card in question fails again, 
replace it. 
if the System Processor must be 
replaced, then the system must be...

Commissioning 
Peripheral Subsystem Tests 
5.4 The following chart details the steps required to perform peripheral subsystem tests 
on an SX-2OOOSG system. 
Note: If peripheral redundancy is not provided, references to Plane B should be ignored, except 
for the Peripheral Switch Matrix (PSM) card in slot 27. This card connects the Peripheral 
Subsystem Controllerto the Peripheral Interface cards in the second plane of a peripheral 
pair; i.e., the PSM in plane B is driven by the processor in plane A and...

m IA 
SX-2000 SG ICS Commissioning 
Chart 5-4 SX-2000 SG Peripheral Subsystem Tests 
(continued) 
abinet Number DIP switch 
WARNING: DUPLICATE PERIPHERAL REPORTS 
RECEIVED FOR CABINET XX SHELF XX CHECK 
CAB. DIP SWITCH SElTINGS, ENTER  TO 
PRINT PERIPHERAL CONFIGURATION 
Begin testing the Peripheral Process 
Switch Matrix cards by entering the following 
Disable all tests previously enabled 
TEST 29 of the specified shelf and slot 27 
of the partner shelf of the pair. As 
each slot is tested, a test...

Chart 5-4 SX-2000 SG Peripheral Subsystem Tests 
(continued) 
Step Action Comments 
9. 
Test PlCs on Peripheral Shelf 3 by entering: 
STEST Suppress all previous testing. 
ETEST l-24 Enable testing of slots 1 - 24. 
TEST Test cards in slots 1 -24. 
If the test on a slot is successful, the system 
responds with: 
0O:OO:OO 000 TEST COMPLETE - NO ERRORS ON 
SLOT NUMBER xx (cabinet number) (shelf number) 
(test number) (pass number) 
and the system proceeds to test the next slot. 
If errors are detected, an...